763642

Ferm CDM1134 Manual

6
Zoom out
Zoom in
Previous page
1/36
Next page
6
EN
Description
The numbers in the text refer to the diagrams on
pages 2 - 3
Fig. A
1. Machine
2. Battery
3. Battery unlock button
5. Charger
6. Charger LED indicator
7. Chuck
8. Gear selection switch
9. Direction switch
10. On / off switch
11. Torque adjustment ring
12. Work light
3. OPERATING
The battery must be charged before first
use.
Removing the battery from the machine
Fig. B1 + B2
• Push the battery unlock buttons (3) and pull
the battery out of the machine like shown in
Fig. B1.
Inserting the battery into the machine
Fig. B1 + B2
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
• Insert the battery (2) into the base of the
machine as shown in Fig. B2.
• Push the battery further forward until it clicks
into place.
Charging the battery (with the charger)
Fig. C
• Plug the charger plug into an electrical outlet
and wait for a while. The LED indicator on
the battery (6) will lighten up and show the
charging status.
LED indicator (6)
Fig. C
The battery has 1 LED indicator (6) which
indicates the status of the charging process:
LED Charger status
Red Battery charging in progress
Green Battery charging finished, battery fully charged
• After the battery is fully charged remove the
charger plug from the outlet and remove the
battery from the charger.
When the machine is not being used over
a longer period of time it is best to store
the battery in charged condition.
Fitting and removing drills or screwdriver bits
Fig. D
Always remove the battery before
mounting an accessory.
The drill chuck (7) is suitable for drills and screw driver
bits with round shaft as well as hexagonal shaft.
• Hold the machine firmly with one hand
• Open the drill chuck (7) by rotating the chuck
with your other hand in clockwise direction until
it is opened far enough for the bit to slide in.
• Insert the shaft of the drill or screwdriver bit
• Tighten the drill chuck again by firmly rotating
the chuck (7) counterclockwise.
• Check if the bit is centered well by shortly
activating the machine´s on/off switch.
Adjusting the gears
Fig. D
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between both
positions, this will damage your machine.
The machine has 2 drill speeds, which can be
adjusted by sliding the gear switch (8) forward or
backwards. The number on the gear switch (8)
shows which position is chosen.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1134 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1134 in the language / languages: English, German, Dutch, French, Polish as an attachment in your email.

The manual is 6,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info