762255
7
Zoom out
Zoom in
Previous page
1/40
Next page
7
EN
Red LED
status:
Green LED
status: Charger status
Off Off No power
Off On
Standby mode:
-No battery is inserted or,
-Battery inserted but charging has
finished
On Off Battery charging in progress
• Fullychargingthebatterymaytakeupto180
minutes.
• Afterthebatteryisfullychargedremovethe
charger plug from the outlet and remove the
battery from the charger.
• Thebatterycanbestoredordirectlyinstalled
on the machine.
Lithium-Ion cells can be stored for a long
period without losing much of their
charge. When the machine is not being
used over a longer period of time it is
best to store the battery in charged
condition.
Fitting and removing sockets
Always remove the battery before
mounting an accessory.
To mount the socket, firmly push it bit with even
pressure on the machine.
To remove the socket, firmly pull it off the
machine.
Adjusting the direction of rotation
• Setthedirectionswitch(7)toposition” in
order to drive screws.
• Setthedirectionswitch(7)toposition” in
order to remove screws
Switching the machine on and off
WARNING: Ensure fastener and/or system will
withstand the level of torque generated by the
tool.
Excessive torque may cause breakage and
possible personal injury.
WARNING:Do not use regular socket wrench type
sockets;use only those impact wrenchs.
Socketsnotdesignedforimpactwrenchescould
break and result in personal injury.
Inspect sockets prior to use to ensure that they
have no cracks or other visible damage.
1. Place the accessory on the fastener head.
Keepthetoolpointedstraightatthefastener.
2.Pressingtheon/offswitch(8)willactivate
the machine, the further the switch is being
pushed, the faster the drill will turn. Releasing
theon/offswitch(8)willstopthemachine.
Always check torque with a torque wrench,
as the fastening torque is affected by many
factors including the following:
• Voltage:Lowvoltage,duetoanearly
discharged battery, will reduce fastening
torque.
• Accessorysize:Failuretousethecorrect
accessory size will cause a reduction in
fastening torque.
• Boltsize:Largerboltdiametersgenerally
require higher fastening torque. Fastening
torque will also vary according to length,
grade, and torque coefficient.
• Bolt:Ensurethatallthreadsarefreeofrustand
other debris to allow proper fastening torque.
• Material:Thetypeofmaterialandsurface
finish of the material will affect fastening
torque.
• Fasteningtime:Longerfasteningtimeresults
inincreasedfasteningtorque.Usingalonger
fastening time than recommended could
cause the fasteners to be overstressed,
stripped or damaged.
• Movethedirectionreversingswitch(7)tothe
middle position to lock the movement of the
on/off switch. It cannot be activated in this
position.
Only lay down the machine when it has
stopped running completely. Do not
place it on a dusty surface as particles of
dust could get into the mechanism.
Work light (9)
Fig. A
The machine is equipped with a work light to
illuminate the work location.
• Itautomaticallyswitchesonwhentheon/off
switch is being pressed.
• Itautomaticallyswitchesoffwhentheon/off
switch is released again.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1127 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1127 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 6,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info