632676

Ferm CDM1114S Manual

9
Zoom out
Zoom in
Previous page
1/156
Next page
9
EN
sleeve (8) with your other hand in clockwise
direction until it is opened far enough for the
bit to slide in.
 Insert the shaft of the drill or screwdriver bit
 Tighten the drill chuck again by firmly rotating
the chuck sleeve (8) counterclockwise.
 Check if the bit is centered well by shortly
activating the machine´s on/off switch.
Adjusting the gears
Fig. F
Never switch gears when the motor is
running, this will damage your machine.
Never put switch in the middle between
both positions, this will damage your
machine
The machine has 2 drill speeds, which can be
adjusted by sliding the gear switch (9) forward or
backwards. The number on the gear switch (9)
shows which position is chosen.
 Position 1: For slow drilling, large drilling
diameter or screw driving. The machine has
high power at a low speed.
 Position 2: For fast drilling or small drilling
diameter
Adjusting the direction of rotation
Fig. G
 Set the direction switch (10) to position “” in
order to drive screws or to use it for drilling.
 Set the direction switch (10) to position “” in
order to remove screws
Switching the machine on and off
Fig. G
The on/off switch (11) is used for activating the
machine and adjusting rotation speed.
 Pressing the on/off switch (11) will activate
the machine, the further the switch is being
pushed, the faster the drill will turn.
 Releasing the on/off switch (11) will stop the
machine.
 Move the direction reversing switch (10) to the
middle position to lock the movement of the
on/off switch. It cannot be activated in this
position.
Only lay down the machine when it has
stopped running completely. Do not
place it on a dusty surface as particles of
dust could get into the mechanism.
Adjusting the torque
Fig. G
The machine has 23 different torque settings
and a special drill mode to set the power being
transmitted to the chuck.
By rotating the torque adjustment ring (12),
screws can be driven to a predetermined depth,
which is ideal for repetitive work. The higher the
number, the more torque will be transmitted.
 Select a low setting for small screws or soft
work material.
 Select a high setting for large screws, hard
work materials and when removing screws.
 You should preferably choose a setting as
low as possible when driving screws. Select
a higher setting if the motor slips before the
screw is fully tightened.
 For drilling, turn the torque adjustment ring
(12) to the setting for drilling by fully turning it
counterclockwise.
Ensure that the direction switch (10) is
always set to during drilling.
The machine is equipped with electronic
overload protection function. When the
machine gets overloaded it will shut
down automatically. When this happens,
please wait for at least 5 seconds to let
the overload protection reset itself.
Work light (13)
Fig. A
The machine is equipped with a work light to
illuminate the work location.
 It automatically switches on when the on/off
switch is being pressed.
 It automatically switches off when the on/off
switch is released again.
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1114S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1114S in the language / languages: All languages as an attachment in your email.

The manual is 22,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info