632675
8
Zoom out
Zoom in
Previous page
1/156
Next page
8
EN
3. OPERATING
The battery must be charged before first
use.
Removing the battery from the machine
Fig. B
 Hold the machine (1) firmly with one hand
 Push down the battery unlock button (3)
located on the rear side of the battery (2) with
the other hand.
 Keep pushing this button (3) down and slide
the battery backwards out of the machine, like
shown in Fig. B.
Inserting the battery into the machine
Fig. B
Ensure that the exterior of the battery is
clean and dry before connecting to the
charger or machine.
 
 Insert the battery (2) into the base of the
machine as shown in Fig. B.
 Push the battery further forward until it clicks
into place.
Checking the battery charging status
Fig. C
The included battery is delivered in partly
charged condition.
 To check the battery charge status, push the
button (4) on battery shortly.
 The battery has 4 lights indicating the charge
level, the more lights that burn, the more
charge the battery has left.
 When the lights are burning RED it means
the battery is empty and must be charged
immediately.
Charging the battery (with the charger)
Fig. D
 Take the battery (2) from the machine
 Turn the battery (2) to upside down position
and slide it onto the charger (5) as shown in
Fig. D.
 Push the battery until it is fully pushed into the
slot.
 Plug the charger plug into an electrical outlet
and wait for a while. The LED indicators on
the charger (6) will lighten up and show the
charger status.
LED indicators (6)
Fig.D
The charger has 2 LED indicators (6) which
indicate the status of the charging process:
Red LED
status:
Green LED
status:
Charger status
Off Off No power
Off On
Standby mode:
-No battery is inserted or,
-Battery inserted but charging has
finished more then 2 hours ago
On Off Defective battery
Blinking Off Battery charging in progress
Off Blinking
Battery charging finished, battery
fully charged
On On
Battery is too hot, charging
progress is on hold. Charging will
start automatically after the battery
has cooled down.
 Fully charging the battery may take up to 60
minutes.
 After the battery is fully charged remove the
charger plug from the outlet and remove the
battery from the charger.
 The battery can be stored or directly installed
on the machine.
Lithium-Ion cells can be stored for a long
period without losing much of their
charge. When the machine is not being
used over a longer period of time it is
best to store the battery in charged
condition.
Fitting and removing drills or screwdriver bits
Fig. E
Always remove the battery before
mounting an accessory.
The drill chuck (7) is suitable for drills and
screwdriver bits with round shaft as well as
hexagonal shaft.
 Hold the machine firmly with one hand
 Open the drill chuck (7) by rotating the chuck
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1113S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1113S in the language / languages: All languages as an attachment in your email.

The manual is 22,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info