Manual Ferm CDM1094 (page 6 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

539082

Zoom out

Zoom in

1/52

Ferm

• To remove the bit, slide and hold the locking

sleeve to the rear.

Mode selection lever

Fig.B

• Setthemodeselectionlevertothehammer

position for hammer drilling in concrete and

stone. Do not use this selection for any other

applications.

• Setthemodeselectionlevertothedrilling

without impact position for drilling in wood,

metal, ceramic and plastic. This setting is also

used for screwdriving.

The On/Off switch

Fig. A

• Switch the machine on by pressing the

triggerswitch (2). When you release the

triggerswitch (2) the machine will turn off.

Switching the direction of rotation

• Direction of rotation counter-clockwise: shift

switchto“►”.

• Direction of rotation clockwise: shift switch to

“◄”.

Chuck

A chuck with SDS-10 shaft is shipped with

the product. Please note that the machine is

particularly suited for hammer drilling, the chuck

should only be used for occasional simple drill

work.

• To open the keyless drill chuck, rotate the

chuck body in a clockwise direction until the

jaws open wide enough to accept the bit.

• Insert the bit, over the full length of the jaws,

into the chuck.

• Tighten the chuck jaws onto the bit by turning

the chuck body in a counter clockwise

direction.

The bit must be properly inserted with all

three of the chuck jaws holding the bit

centred in the chuck. Make sure the

chuck jaws grasp the flat sides of a

screwdriver bit. Failure to do so could

cause the bit to be thrown from the

chuck, resulting in possible serious

injury or damage to the chuck

To remove a bit, open the keyless drill chuck by

rotating the chuck body in a clockwise direc tion

until the chuck jaws open and remove the bit.

The adapter can only be used for drilling/

screwdriving without impact. Never use the

adapter with the machine set to Hammer mode.

Hammer drilling in concrete or brick

Caution: Stone drills can get very hot.

It may be necessary to drill with smaller bits and

re-drill to nominal size so that later the plug is

firmly seated.

For large bores, for instance in very hard concrete,

use a smaller bit for pilot drilling and re-drill to

nominal size.

Do not apply a lot of pressure on the machine, let

the machine do the work, guiding the machine with

light pressure is sufficient.

Hold the machine with both hands. The bit can

jam, particularly with deep bores, and the machine

will turn. This can lead to serious injury.

Battery status indicator

The battery status indicator shows the charge

condition of the battery for a few seconds when

the On/Off switch is pressed fully or halfway.

• When 1 LED is lit, the charge is less than 30%

and the battery should be charged.

• When 2 LEDS are lit, the battery is charged

between 30 and 70%.

• When 3 LEDS are lit, the battery is charged

between 70 and 90%.

• When all 4 LEDS are lit, the battery is fully

charged.

Charging the battery

• Plug the adapter directly into the charger

connection (8). Charging will start when the

adapter is plugged into the mains supply.

Temperature overload protection

When using as intended for, the power tool can’t

be subject to overload. When the load is too high

or the battery temperature exceeds 70 ºC, the

electronic control switched off the power tool until

the temperature is within working range again.

The battery status indicator (4) flashes green until

the On/Off switch is released.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1094 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CDM1094 Manual

Product: