510081
5
Zoom out
Zoom in
Previous page
1/60
Next page
EN
5
Ferm
The number of revolutions of the
machine can be electronically set.
Do not use in rain.
Indoor use only.
Ni-Cad batteries can be recycled. Drop
them off at a disposal center for
chemical wastes, so that they can be
recycled or disposed of in an eco-
friendly manner.
Always recycle batteries
Important safety notes on charger and battery
block
If you come in contact with acid from the
battery block, rinse it off with water
immediately. If acid gets into your eyes,
rinse out your eyes at once with water
and contact a doctor immediately!
1. Read and note the operating instructions and
safety notes for the charger and battery block
before use!
2. NB! Only use the charger and battery block
that were supplied by the manufacturer -
otherwise you will risk an accident.
3. Protect the charger, battery block and power
tool from moisture, e.g. rain or snow.
4. Always check that all cables are connected
correctly before using the charger.
5. If you discover that a cable is damaged, you
should not use the charger again. Have the
damaged cable replaced immediately.
6. When the charger is not in use, the mains plug
should be removed from the power socket. Do
not pull out the plug by grasping the cable.
7. If the charger has been dropped or has
otherwise been exposed to high mechanical
stresses, you should have it checked for
damage by an authorised dealer before using
it again. Damaged parts should be repaired.
8. Exercise caution when handling the battery
block and do not drop it or expose it to
impacts.
9. Never attempt to repair the charger or battery
block yourself. Repairs must always be carried
out by an authorised dealer - otherwise you
risk an accident.
10. Before cleaning or servicing the charger or
battery block, always pull the plug from the
charger socket.
11. Never charge the battery block when the
ambient temperature is below 5 °C or above
40°C.
12. The air vents in the charger must never be
blocked.
13. The battery block must not be short-circuited.
A short-circuit will cause a high current
to flow. This may result in overheating,
the danger of fire or explosion of the
battery block. This may damage the
battery block or the user may risk an
accident.
Therefore:
• Do not connect any cables to the poles of
the battery block.
• Take care that there are no metal objects
(nails, paper clips, coins, etc.) on the
contact surface of the battery block.
• Do not expose the battery block to water
or rain.
• Only use the battery block supplied
in combination with this cordless drill/
screwdriver so as to avoid faults and/or
risks to persons.
14. A damaged battery block or one that can
no longer be charged must be disposed
of as special waste. Do not discard it with
household waste.
15. Never throw the battery block onto a fire or
into water. This will risk explosion!
Electrical safety
Always check that the voltage on the
battery block corresponds to the voltage
on the rating plate. Also check that your
mains voltage corresponds to the input
voltage of the battery charger.
Class II machine – Double insulation –
You don’t need any earthed plug.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1090 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1090 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info