Manual Ferm cdm1077 swing drill (page 8 of 68) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388433

Zoom out

Zoom in

1/68

8 Ferm

For fast drilling set the speed selection switch •

to ‘2’.

Never switch over when the motor is

running!

The pivot lock knob (4)

Fig. D

Turn the knob (4) anti clockwise to unlock the

head’s swing movement. The pivoting angle of the

chuck can be adjusted in 5 different positions

(0/22,5/45/67,5/90 degrees).

To lock again, rotate the knob clockwise when the

head is in the correct position. This can be felt by a

click.

Make sure the head’s swing movement

is locked before use by turning the knob

clockwise until it is locked. If it is not

possible to rotate the pivot lock knob (4),

move the head until this knob can rotate.

Then rotate the knob into its lock

position.

The rotation lock ring (2)

Fig. E

With the use of this ring the chuck can be rotated

360 degrees in 24 steps. Pull the ring backwards

and rotate the chuck into the required position.

Release the ring to lock the chuck into position.

Driving and removing screws

Fig. A

Set the direction reversing switch (5) to position

‘’ in order to drive screws.

Set the direction reversing switch (5) to position

‘’ in order to remove screws.

Ensure that the direction reversing

switch (5) is always set to ‘’ during

drilling.

Switching the device on and off

Fig. A

Depress the on/off switch (8). It regulates the •

speed of the appliance by transmitting power to

the switch.

Release the on/off switch (8) to halt the drill •

chuck immediately, it will no longer run on.

Move the direction reversing switch (5) to the •

centre in order to lock the appliance in its

disabled state.

Only lay down the appliance when it has stopped

running completely. Do not place it on a dusty

surface as particles of dust could get into the

mechanism.

Charging the battery

Fig. F

The FDCDL-1800 battery charger is only suitable

for charging batteries of type FDCDB-1800.

Place the battery inside the charger, as shown •

on the illustration. Pay attention to + and - pole

markings.

Insert the charger plug into a power socket. •

The red rapid charging lamp should now be

illuminated.

As soon as the green trickle charging lamp •

lights up, charging has been completed and the

device is ready for operation.

Only use the charger in a dry

environment at temperatures between

5˚Cand40˚C.

The battery in your drill was not charged up at the

factory. Before using it for the first time, you should

charge it for approx. 1 - 2 hours so that it reaches

full capacity. The final capacity of the battery is

reached after 4 - 5 battery cycles.

Discharging the battery

Not only charging batteries is important,

discharging is of equal importance or

even greater importance.

When the battery is charged the cordless drill •

has to be used until you start noticing that the

power of the drill is diminishing and that the

maximum rotational speed is not reached.

The battery is almost discharged now. Only •

now you can start charging the battery.

Charging the battery while it is still charged for •

say one-third of capacity, the so-called

‘memory effect’ can occur. Since during

charging only the discharged part of the battery

capacity of the battery is being charged now,

the battery can start crystallizing in the one-

third that is still charged. This part of the battery

capacity can never be used afterwards.

Do not discharge the battery to the minimum. •

As soon as you notice that the power or the

maximum rotational speed is diminishing, you

have to charge the battery.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm cdm1077 swing drill in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 13,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm cdm1077 swing drill Manual

Product: