538821

Ferm CDM1075 FDCD-1440LK Manual

7
Zoom out
Zoom in
Previous page
1/56
Next page
GB
7
Ferm
Loosen the drill chuck (6) by rotating the hand-•
grip (8).
Insert the shaft of the drill cutter into the chuck.•
Tighten the drill chuck so that the drill cutter is •
firmly clamped.
Rotate the drill chuck in the opposite direction •
when you wish to change the cutter.
Connecting and removing the battery
Fig.C
Ensurethattheexteriorofthebattery
blockortooliscleananddrybefore
connectingthecharger.
Ensure that the direction reversing switch •
(1, Fig. A) is in the central position in order to
prevent the appliance from being switched on
unexpectedly.
Insert the battery (3) into the base of the •
appliance, as shown on the illustration. Push
the battery until it latches in.
Press the locking buttons (2) on both sides •
before removing the battery, and disengage
the battery from the base of the appliance.
OPERATION
4. OPERATION
Alwaysfollowthesafetynotesandthe
relevantsafetycode.
Hold the appliance firmly and press the drill
steadily onto the workpiece. Do not overload
the appliance. Only use drills with no visible
wear. Worn drills will have a bad effect on the
functioning of the appliance.
Adjusting the speed
Fig.D
The appliance has two drill speeds.
For slow drilling or for driving or removing •
screws, set the speed selection switch (7) to ‘1’.
For fast drilling set the speed selection switch •
(7) to ‘2’.
Neverswitchoverwhenthemotoris
running!
Adjusting the torque
Fig.E
The appliance has 16 different torque settings
with which to set the power for driving and
removing screws.
Set the torque adjustment ring (5) to the •
desired position. The available torque settings
are indicated on the adjustment ring by the
numbers 1 to 8 and by dots between the
figures to define intermediate settings (16 in
total).
You should preferably choose a setting as •
low as possible when using the screwdriver.
Select a higher setting if the motor slips.
Driving and removing screws
Fig.A
Set the direction reversing switch (1) to •
position ‘’ in order to drive screws.
Set the direction reversing switch (1) to •
position ‘±’ in order to remove screws.
Drilling
Rotate the torque adjustment ring (5) to the •
drilling position.
Ensurethatthedirectionreversing
switch(1)isalwayssetto‘’during
drilling.
Switching the device on and off
Fig.A
Depress the on/off switch (4). It regulates the •
speed of the appliance by transmitting power
to the switch.
Release the on/off switch (4) to halt the drill •
chuck immediately, it will no longer run on.
Move the direction reversing switch (1) to the •
centre in order to lock the appliance in its
disabled state.
Only lay down the appliance when it has stopped
running completely. Do not place it on a dusty
surface as particles of dust could get into the
mechanism.
Charging the battery
The included battery is delivered in partly •
charged condition.
Only use the battery charger in a temperature •
range between + 5 °C to + 40 ºC.
Only use the battery charger in dry, ventilated •
rooms.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1075 FDCD-1440LK at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1075 FDCD-1440LK in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info