538819
6
Zoom out
Zoom in
Previous page
1/28
Next page
Ferm 51
Hvis akku-boremaskinen ikke skal
bruges i en længere periode, skal
batteriet lades helt op forinden.
Batteriet skal være opladet under
opbevaringen.
5. SERVICE &
VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under
strøm, når der udføres
vedligeholdelsesarbejder
mekanikken.
Maskinerne er udviklet til at fungere længe uden
problemer med et minimum af vedligeholdelse.
Ved at rengøre maskinen regelmæssigt og
behandle den korrekt, bidrager De til en længere
levetid for maskinen.
Rengøring
Rengør regelmæssigt maskinkappen med en
blød klud, helst efter hvert brug. Sørg for at
ventilationshullerne er fri for støv og snavs. Brug
en blød klud, der er vædet i sæbevand til at
fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, som benzin, alkohol,
ammoniak, osv. Den slags stoffer beskadiger
kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Skulle en fejl opstå, f.eks. pga. slidtage af en
enhed, kontakt venligst serviceadressen
garantibeviset. bagsiden af denne manual
finder du en tegning med alle dele, der kan
bestilles.
Miljø
For at undgå transportbeskadigelse leveres
maskinen i en solid emballage. Emballagen er
vidt muligt lavet af genbrugsmateriale. Genbrug
derfor emballagen. NiCd celler kan genvindes.
Defekte og/eller kasserede elektriske
eller elektroniske maskiner skal
afleveres en genbrugsplads.
Garanti
Læs det separat vedlagte garantikort for
garantibetingelserne.
DK
06 Ferm
The tool is suitable for use as a screwdriver
and drill. Any other application is specifically
excluded.
3. MOUNTING ACCESSORIES
Prior to mounting an accessory always
remove the battery.
Fitting and removing drill cutters
Fig. B
In addition to drill cutters, the tool can also
accommodate screwdriver bits with a hexagonal
shaft.
Loosen the drill chuck (3) by rotating the
hand-grip (9).
Insert the shaft of the drill cutter into the chuck.
Tighten the drill chuck so that the drill cutter is
firmly clamped.
Rotate the drill chuck in the opposite direction
when you wish to change the cutter.
Connecting and removing the battery
Fig. C
Ensure that the exterior of the battery
block or tool is clean and dry before
connecting the charger.
Ensure that the direction reversing switch (5
Fig. A) is in the central position in order to
prevent the appliance from being switched on
unexpectedly.
Insert the battery (4) into the base of the
appliance, as shown on the illustration. Push
the battery until it latches in.
Press the locking buttons (10) on both sides
before removing the battery, and disengage
the battery from the base of the appliance.
4. OPERATION
Always follow the safety notes and the
relevant safety code.
Hold the appliance firmly and press the drills
steadily onto the workpiece. Do not overload the
appliance. Only use drills with no visible wear.
Worn drills will have a bad effect on the
functioning of the appliance.
Adjusting the torque
Fig. D
The appliance has 16 different torque settings
with which to set the power for driving and
removing screws.
Set the torque adjustment ring (2) to the
desired position. The available torque settings
are indicated on the adjustment ring by the
numbers 1 to 8 and by dots between the
figures to define intermediate settings (16 in
total).
You should preferably choose as low a setting
as possible when using the screwdriver.
Select a higher setting if the motor slips.
Driving and removing screws
Set the direction reversing switch (5) to
position 'R' in order to drive screws.
Set the direction reversing switch to position
'L' in order to remove screws.
Drilling
Rotate the torque adjustment ring (2) to the
drilling position.
Ensure that the direction reversing
switch (5) is always set to 'R' during
drilling.
Switching the device on and off
Fig. A
Depress the on/off switch (1). It regulates the
speed of the appliance by transmitting power
to the switch.
Release the on/off switch (1) to halt the drill
chuck immediately which will no longer run on.
Move the direction reversing switch (5) to the
centre in order to lock the appliance in its
disabled state.
Only lay down the appliance when it has stopped
running completely. Do not place it on a dusty
surface as particles of dust could get into the
mechanism.
Charging the battery
Fig. E
Place the battery (5) inside the charger (11),
as shown on the illustration. Pay attention to
+ and - pole markings.
Insert the charger plug into a power socket.
The red rapid charging lamp (12) should
now be illuminated.
GB
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm CDM1072 EBF-18K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM1072 EBF-18K in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 19,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info