389294

Ferm cdm 1079 fpcd1800l Manual

6
Zoom out
Zoom in
Previous page
1/56
Next page
GB
6 Ferm
Insert the depth rod into the matching hole in •
the depth stop rod mounting clamp.
Position the depth stop rod so it will contact •
the work piece when the drill reaches the
appropriate depth.
When the depth stop rod is properly •
positioned, tighten the depth stop rod
mounting clamp by turning the auxiliary handle
clockwise.
Tighten the handle by hand only. Do not
over tighten the handle or you will
damage the handle or the housing.
Installing drill bits
Fig. 4
Never hold the chuck and use the drill
power to loosen or tighten bits. This can
result in serious injury.
To open the keyless drill chuck, rotate the •
chuck body (1) in a clockwise direction until
the jaws open wide enough to accept the bit.
Insert the bit, over the full length of the jaws, •
into the chuck.
Tighten the chuck jaws onto the bit by turning •
the chuck body in a counter clockwise
direction.
As the chuck jaws begin to tighten on the bit, •
you will hear a clicking sound. Continue to
rotate the chuck body until the clicking stops
and you can no longer turn it any further by
hand. The chuck is now locked.
The bit must be properly inserted with all
three of the chuck jaws holding the bit
centred in the chuck. Make sure the
chuck jaws grasp the flat sides of a
screwdriver bit. Failure to do so could
cause the bit to be thrown from the
chuck, resulting in possible serious
injury or damage to the chuck.
To remove a bit, open the keyless drill chuck by •
rotating the chuck body in a clockwise direc tion
until the chuck jaws open and remove the bit.
Connecting and removing the battery
Fig. 1
Ensure that the direction reversing switch (4) is •
in the central position in order to prevent the
appliance from being switched on unexpectedly.
Insert the battery into the base of the •
appliance, as shown on the illustration. Push
the battery until it latches in.
Press the locking button (6) on either side •
before removing the battery, and disengage
the battery from the base of the appliance.
Only use batteries of the following type. Using any
other batteries could cause serious injury or
damage the tool.
CDA1051: FPB-1800L, 18V Lithium-Ion
CDA1053: FPB-1800N, 18V NiMH
The following charger can be used to charge these
batteries.
CDA1052: FPL-1800 (Lithium-Ion and NiMH)
CDA1054: FPL-1800N (NiMH only)
4. OPERATION
Always follow the safety notes and the
relevant safety code.
Hold the appliance firmly and press the drill
steadily onto the workpiece. Do not overload the
appliance. Only use drills with no visible wear.
Worn drills will have a bad effect on the functio-
ning of the appliance. Do not cover the air vents.
This will reduce the motor cooling, and possibly
lead to overheating the motor.
Switch for percussion drilling
Fig. 1
With the switch on top of the machine you can
select normal or percussion drilling.
• Slidetheswitchtothe“Drill”symbolfor
normal drilling.
• Slidetheswitchtothe“Hammer”symbolfor
percussion drilling.
Driving and removing screws
Fig. 1
Set the direction reversing switch (4) to •
position‘►’inordertodrivescrews.
Set the direction reversing switch (4) to •
position‘◄’inordertoremovescrews.
Ensure that the direction reversing
switch (4) is always set to ‘►’ during
drilling.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm cdm 1079 fpcd1800l at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm cdm 1079 fpcd1800l in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info