Manual Ferm cdm 1076 (page 6 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

388434

Zoom out

Zoom in

1/64

6 Ferm

Specific safety instructions:

The tool is suitable for use as a screwdriver,

regular drill and impact drill. Any other application

is specifically excluded.

Use only impact drill bits and accessories that •

are designed for use with an impact drill when

using this machine in the impact drill mode.

Standard drill bits are NOT designed for use in

an impact drill and must NOT be used with an

impact drill. They may shatter and possibly

cause serious injury.

Do not drill material too small to be securely •

held.

Always keep hands out of the path of the drill •

bit. Avoid awkward hand positions where a

sudden slip could cause your hand to move

into the path of the drill bit.

Secure work piece. Use clamps or a vice to •

hold the work piece. It is safer than using your

hand and it frees both hands to operate the

tool.

Make sure there are no nails or foreign objects •

in the part of the work piece to be drilled.

To avoid injury from accidental starting, always •

remove the battery from the tool before

installing or removing a drill bit.

Do not install or use any drill bit that exceeds •

175 mm (7”) in lengths or extends more than

150 mm (6”) beyond the chuck jaws. They can

bend or break suddenly.

Before starting the operation, jog the switch •

shortly to make sure the drill bit does not

wobble or vibrate.

Do not use fly cutters or multiple-part hole •

cutters, as they can come apart or become

unbalanced during use.

Make sure the spindle has come to a complete •

stop before touching the chuck or attempting

to change the drill bit.

Always make sure the chuck is tight and the •

drill bit firmly tightened in the chuck before

starting the drill.

When drilling into smooth, hard surfaces such •

as metal, use a centre punch to mark the desi-

red hole location. This will prevent the drill bit

from slipping off centre as the hole is started.

Use a masonry bit with the drill in impact mode •

ONLY when drilling in concrete or masonry.

Always use carbide tipped masonry bits when •

drilling in concrete or masonry

This appliance is not intended for use by •

persons (including children) with reduced

sensory or mental capabilities, or lack of

experience and knowledge, unless they have

been given supervision or instructions

concerning use of the appliance by a person

responsible for their safety.

Children should be supervised to ensure that •

they do not play with the appliance.

Follow all safety rules and warnings,

also those which are included with the

battery pack and charger used with this

tool. Failure to do so may result in

serious injury or damage to the charger

and the battery pack

3. MOUNTING ACCESSORIES

Prior to mounting an accessory always

remove the battery.

Installing the auxiliary handle

Fig. 2 + 3

Install the auxiliary handle for two handed

operation of the drill. This is particularly important

for impact drilling in concrete. The auxiliary handle

can be installed on either the left or right side of

the combi drill.

Insert the threaded mounting screw through •

the depth stop rod clamp (14) and into the

threaded hole in the housing.

Turn the auxiliary handle (11) clockwise to •

tighten it into the housing.

Make sure the key on the depth stop

clamp is aligned with the notch in the

drill housing. This will prevent it from

unexpected turning and the auxiliary

handle from coming loose.

Screwdriver bits and drill bits can be stored in the

auxiliary handle.

To remove the end cap (15), pull it of the auxiliary

handle. To install, push it back on the auxiliary

handle.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm cdm 1076 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm cdm 1076 Manual

Product: