Manual Ferm CDM 1064 (page 7 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

79275

Zoom out

Zoom in

1/64

Ferm

Installing the depth stop rod

Fig. 1 + 2

The depth stop rod (13) is used as a gauge to

control the depth of the drilled hole. It can be used

with the combi drill in either the normal drilling

mode or the impact drill mode.

Turn the auxiliary handle (11) counter •

clockwise about three turns to open the depth

stop rod mounting clamp (14).

Insert the depth rod into the matching hole in •

the depth stop rod mounting clamp.

Position the depth stop rod so it will contact •

the work piece when the drill reaches the

appropriate depth.

When the depth stop rod is properly •

positioned, tighten the depth stop rod

mounting clamp by turning the auxiliary handle

clockwise.

Tighten the handle by hand only. Do not

over tighten the handle or you will

damage the handle or the housing.

Installing drill bits

Fig. 4

Never hold the chuck and use the drill

power to loosen or tighten bits. This can

result in serious injury.

To open the keyless drill chuck, rotate the •

chuck body (1) in a clockwise direction until

the jaws (16) open wide enough to accept the

bit. (17)

Insert the bit, over the full length of the jaws, •

into the chuck.

Tighten the chuck jaws onto the bit by turning •

the chuck body in a counter clockwise

direction.

As the chuck jaws begin to tighten on the bit, •

you will hear a clicking sound. Continue to

rotate the chuck body until the clicking stops

and you can no longer turn it any further by

hand. The chuck is now locked.

The bit must be properly inserted with all

three of the chuck jaws holding the bit

centred in the chuck. Make sure the

chuck jaws grasp the flat sides of a

screwdriver bit. Failure to do so could

cause the bit to be thrown from the

chuck, resulting in possible serious

injury or damage to the chuck.

To remove a bit, open the keyless drill chuck by •

rotating the chuck body in a clockwise direc tion

until the chuck jaws open and remove the bit.

Connecting and removing the battery

Fig. 1 + 5

Ensure that the direction reversing switch (8) •

is in the central position in order to prevent the

appliance from being switched on

unexpectedly.

Insert the battery into the base of the •

appliance, as shown on the illustration. Push

the battery until it latches in.

Press the locking button (10) on either side •

before removing the battery, and disengage

the battery from the base of the appliance.

Only use batteries of the following type. Using any

other batteries could cause serious injury or

damage the tool.

CDA1051: FPB-1800L, 18V Lithium-Ion

CDA1053: FPB-1800N, 18V NiMH

The following charger can be used to charge these

batteries.

CDA1052: FPL-1800 (Lithium-Ion and NiMH)

CDA1054: FPL-1800N (NiMH only)

4. OPERATION

Always follow the safety notes and the

relevant safety code.

Hold the appliance firmly and press the drill

steadily onto the workpiece. Do not overload the

appliance. Only use drills with no visible wear.

Worn drills will have a bad effect on the functio-

ning of the appliance. Do not cover the air vents.

This will reduce the motor cooling, and possibly

lead to overheating the motor.

Adjusting the torque

Fig. 6 + 7

Rotate the adjustment ring (2) to align the correct

torque setting number with the torque indicator

arrow (18). Use the chart below for the correct

torque setting:

1-5: For driving small screws

6-10: For driving medium sized screws into soft

materials

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm CDM 1064 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm CDM 1064 Manual

Product: