510079

Ferm BSM 1021 Manual

5
Zoom out
Zoom in
Previous page
1/104
Next page
5
EN
2. SAFETY INSTRUCTIONS
Explanation of symbols
Denotes risk of personal injury, loss of
life or damage to the tool in case of
non-observance of the instructions in
this manual.
Indicates the presence of an electrical
voltage.
Wear eye protection.
Specic safety instructions
Hold the machine by the insulated gripping
surfaces where the accessory may contact hidden
wiring or the mains cable. If the accessory
contacts a ‘live’ wire, the exposed metal parts of
the machine can also become ‘live’. Risk of
electric shock.
• If you are working with the sanding machine,
wear always ear protectors and dust mask.
• The sanding machine is not suitable for wet
sanding.
• Check if the switch is not in position “ON”,
before you connect the mains plug to the
mains voltage.
• Keep the mains lead always away from
moving parts of the tools.
• Use safety glasses, especially when you sand
above your head.
• Do not bring pressure to your machine, this
will only delay the sanding.
Contact or inhalation of dust coming free
during sanding (e.g. lead painted
surfaces, woods and metals), can
endanger the health of operator and
bystanders. Always wear appropriate
personal equipment as a dust mask and
use the dust bag during sanding.
Immediately switch off the machine when:
• Excessive sparking of the carbon brushes and
verticiliosis in the collector.
• Interruption of the mains plug, mains lead or
mains lead damage.
• Defect switch
• Smoke or stench of scorched isolation
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of re, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Class ll machine. Your machine is double
insulated; therefore no earthwire is
required.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. OPERATION
Always observe the safety instructions
and applicable regulations.
Choice of the sand-paper
Coarse sand-paper (grain 50) removes in general
the bigger part of the material and ne sand-
paper is used for the nishing. If the surface is not
even, then start with rough sand-paper. Further
you use middle coarse sand-paper(grain 80) to
remove the scratches left behind by the coarse
sand-paper and nally you take ne sand-paper
(grain 120) for the nishing.
Removing and Installing the sanding belt
Fig. C
Before assembly the sanding belt always
remove the plug from the mains.
• Put the machine on its side, with the drive belt
cover down wards.
• Loosen the sanding belt fastener (4).
• Remove the sanding belt from the machine
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BSM 1021 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM 1021 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 17,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info