510118

Ferm BGM1020 Manual

4
Zoom out
Zoom in
Previous page
1/44
Next page
EN
4
Indicates the presence of an electrical
voltage.
Keep bystanders away.
Wear eye and ear protection.
Special safety instructions
When using the machine for the first time:
• Check te following:
• Does the voltage rating of the bench
grinder correspond to the power supply?
• Is an earthed mains power socket
available?
• Are the power cord and plug in good
condition (solid, without fraying or other
damage)?
• Avoid the use of long extension cords. The
extension cords you use must always be
earthed.
• A grinding wheel is a brittle toolpiece. The
stone is not resistant to knocks.
• Always grind on the front edge of the grinding
wheel, and never on the side of the grinding
wheel. Never fit a cracked grinding wheel.
Replace it immediately, as the high rotational
speed could cause the stone to fly apart,
causing a serious accident.
• Always wear safety glasses when grinding.
• Never grind without the cover fitted over the
grinding wheel.
• Always fit the grinding wheel cover and tool
rest tightly, and with the correct clearance.
• Never allow more than 1-1.5 mm clearance
between tool rest and grinding wheel.
• Only use the grinding wheel for the work it
was designed for (for example sharpening
tools), and NOT for heavy construction work.
• The following information must be available,
before you fit any new grinding wheel:
• Details about the manufacturer.
• Binding material.
• Dimensions.
• Permissible rotational speed.
• Never ream out the hole in a grinding wheel to
a larger diameter.
• The maximum rotational speed of the grinding
wheel should never be allowed to exceed the
maximum speed given for the wheel.
• Never use any grinding wheel that is
damaged or deformed.
• In order to be able to grind safely, the machine
must be firmly bolted to a workbench.
• The tool rest should be replaced whenever
the width of the tool rest measures less than
20 mm.
• The recommended depth of the recess in the
flange (T) is 2 mm and the diameter of the
spindle hole is 13 mm (see Fig. D).
Whenever using the machine
• Check that the switch is NOT in the ‘ON/1’
position before connecting the machine to the
power supply.
• Always keep the power cord out of the way of
the tool’s moving parts.
Immediately switch off the machine when:
• The plug or power cord is defective or damaged.
• The switch is defective.
• You smell smoke or burning insulation
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
3. installation
The grinder must be firmly bolted to a workbench.
The length of the fixing bolts will depend on the
thickness of the workbench. If the workbench is
made of steel, it is advisable to use a wooden
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BGM1020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BGM1020 in the language / languages: English, German, Dutch, French, Polish, Spanish as an attachment in your email.

The manual is 1,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info