Manual Ferm BGM1010 - FBSM 150-50 (page 5 of 16) (English, German, Dutch, French, Spanish)

632788

Zoom out

Zoom in

1/16

ClEl

■

∆ΗΛΩΣΗ ΣΥΜΜΡΦΩΣΗΣ

(

)

∆ηλώυµε υπευθύνω τι τ πριν αντ είναι

κατασκευασµέν σύµωνα µε τν εή

Καννισµύ ή Κατασκεναστικε σνστάσει:

IEC1029-2-4, EN61029-1, EN55014-1,

EN55014-2, EN61000-3-2, EN61000-3-3

Κατά τι διατάει των Καννισµών τη Κινή Αγρά:

89/392/EEC

73/23EEC

89/336/EEC

απ 01-07-1999

GENEMUIDEN NL

G.M. Ensing

Quality department

28 Ferm

- Attach the sanding paper by loosening the but-

ton in the unit (at the top left) and pushing

downwards the spring.

- Stretch the sanding paper as written herunder.

- Close the cover with help of the three screws.

MOUNTING OF THE SANDING PAPER

- Loosen the knurled knob (A) (see fig. 3), but do

not remove it.

- Place the belt on both rolls. Use your left hand

to compress spring (B) so the belt can be placed

easily.

Correct assembly of the sanding belt pre-

vent unnecessary wear. The sanding belt

has to be assembled as shown in fig 4. With

your hand you can feel which part of the

sanding belt is on top of the weld.

- Retighten the knurled knob and turn over the

sanding belt a view times with your hands.

- If the sanding belt runs of or runs out of line

then use adjustment screw (C) to adjust the san-

ding belt correctly.

- Put the belt under tension by means of nut (D).

ADJUSTING THE TOOL REST

Disconnect the machine and make sure the

sanding belt has stopped before adjusting

the tool rest.

- Loosen nut (E) (see fig. 3) with a spanner.

- Move the tool rest (F) keeping a clearance

between the tool rest and the sanding belt

through which the belt just runs free.

- Retighten nut (E).

- The tool rest can be assembled at two places

depending on the application.

9. MAINTENANCE

While maintaining and cleaning the

machine pull the plug from the mainssoc-

ket. Never use water or other agressive

liquids to clean the machine. Clean the

machine by brushing it with a brush.

REGULAR MAINTENANCE OF YOUR MACHI-

NE PREVENTS PROBLEMS:

- Keep the outside of the belt sander/grinder clean

to ensure accurate operation of all moving parts

and prevent excessive wear.

- Replace the grinding stone and sanding belt

when they are worn.

- There is no need to lubricate the transport rol-

lers of the machine.

10. MALFUNCTION

Below we have listed a number of possible causes

and corresponding solutions in case the machine

does not function as it should:

1. The tool does not work when switched on.

Damaged cord and/or plug.

- Check cord and/or plug.

Defective switch.

- Contact your local Ferm dealer to have the switch

inspected and/or repaired.

2. The temperature of the electric motor

exceeds 70°C.

The motor is defective.

- Contact your local Ferm dealer to have the tool

inspected and/or repaired.

ClEl

■

DECLARATION OF CONFORMITY

(

)

We declare under our sole responsibility that this

product is in conformity with the following

standards or standardized documents

IEC1029-2-4, EN61029-1, EN55014-1,

EN55014-2, EN61000-3-2, EN61000-3-3

in accordance with the regulations.

98/37/EEC,

73/23/EEC,

89/336/EEC

from 26-05-1998

GENEMUIDEN NL

G.M. Ensing

Quality department

Ferm 5

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BGM1010 - FBSM 150-50 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BGM1010 - FBSM 150-50 Manual

Product: