763649

Ferm BCM1022 Manual

13
Zoom out
Zoom in
Previous page
1/24
Next page
13
EN
Trimmer head usage
Always wear eye protection such as
safety goggles. Never lean over the
rotating cutting head. Rocks or other
debris could be thrown into eyes and
face and cause serious personal injury.
Keep the debris guard attached in place
at all times when the unit is operated.
Trimming grass and weeds
Fig. 17
Always remember that the TIP of the line does
cutting. You will achieve better results by not
crowding the line into the cutting area. Allow the
unit to trim at its own pace.
1. Hold the unit so the head is off the ground and
is tilted about 20 degrees toward the sweep
direction.
2. You can avoid thrown debris by sweeping from
your right to the left.
3. Use a slow, deliberate action to cut heavy
growth. The rate of cutting motion will depend
on the material being cut. Heavy growth will
require slower action than will light growth.
4. Never swing the unit so hard as you are in
danger of losing your balance or control of the
unit.
5. Try to control the cutting motion with the hip
rather than placing the full workload on the
arm and hands.
6. Take precautions to avoid wire, grass and
dead, dry, long-stem weeds from wrapping
around the head shaft. Such materials can stall
the head and cause the clutch to slip, resulting
in damage to the clutch system if repeated
frequently.
Adjusting the line length
• Your brush cutters is equipped with a semi-
auto type nylon line head that allows the
operator to advance the line without stopping
the engine. When the line becomes short,
lightly tap the head on the ground while
running the engine at full throttle.
• Each time the head is bumped, the line
advance about 1 inch (25.4 mm). For better
effect, tap the head on bear ground or hard
soil. Avoid bumping in thick, tall grass as the
engine may stall by overload.
Metal blade usage
Fig. 18
When sharpening, removing, or
reattaching the blade, be sure to wear
thick, sturdy gloves and use only proper
tools and equipment to prevent injury.
Choose a suitable recommended cutting
attachment according to the object to be cut.
1. Check the bolt to fasten the blade and be sure
the bolt has no fault, and no abrasion.
2. Be sure that the blade and the holder have been
fastened according to instruction and the blade
turns smoothly without abnormal noise.
3. By using the harness, hang the unit on your
right side. Adjust the harness length so that the
cutting head may become parallel to the ground.
Make sure to use harness and cutting
attachment guard. If not, it is very
dangerous when you slip or lose your
balance.
The rotating parts fastened incorrectly
may cause serious accident to the
operator.
Make sure that the blade is not bent,
warped, cracked, broken or damaged.
If you find any error to the blade, discard
it and change new one.
Cutting method
Fig. 19
1. Use the front left side cutting.
2. Guide the blade from your right to left with it
tilted slightly to your left.
3. When mowing a wide area, start working from
your left end to avoid interference of cut grass.
4. The blade may be seized by weeds if the engine
speed is too low, or the blade cuts too deep into
weeds. Adjust the engine speed and cutting
depth according to the condition of object.
If the grass or other object gets caught in
the blade, or if the unit starts to shake or
vibrate, turn off the engine and check the
whole unit. Change the blade if it has
been damaged.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BCM1022 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BCM1022 in the language / languages: English as an attachment in your email.

The manual is 4,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info