Manual Ferm BCM1022 (page 9 of 24) (English)

763649

Zoom out

Zoom in

1/24

3. After starting the engine, check to make sure

that the cutting attachment stops rotating

when the throttle is moved fully back to its

original position. If it continues to rotate even

after the throttle has been moved fully back,

turn off the engine and take the unit to your

authorized servicing dealer for repair.

Using the product

Cut only materials recommended by the

manufacturer. And use only for tasks

explained in the manual.

1. Grip the handles firmly with both hands using

your whole hand. Place your feet slightly apart

(slightly further apart than the width of your

shoulders) so that your weight is distributed

evenly across both legs, and always be sure to

maintain a steady, even posture while working.

2. Keep cutting attachment below waist level.

3. Maintain the speed of the engine at the level

required to perform cutting work, and never

raise the speed of the engine above the level

necessary.

4. If the unit start to shake or vibrate, turn off the

engine and check the whole unit. Do not use it

until the trouble has been properly corrected.

5. Keep all parts of your body away from rotating

cutting attachment and hot surfaces.

6. Never touch the muffler, spark plug, or other

metallic parts of the engine while the engine

is in operation or immediately after shutting

down the engine. Doing so could result in

serious burns or electrical shock.

If someone comes

1. Guard against hazardous situations at all

times. Warn adults to keep pets and children

away from the area. Be careful if you are

approached. Injury may result from flying

debris.

2. If someone calls out or otherwise interrupts

you while working, always be sure to turn off

the engine before turning around.

Maintenance

1. In order to maintain your product in proper

working order, perform the maintenance and

checking operations described in the manual

at regular intervals.

2. Always be sure to turn off the engine before

performing any maintenance or checking

procedures.

The metallic parts reach high temperatures

immediately after stopping the engine.

3. Under no circumstances should you ever

take apart the product or alter it in any way.

Doing so might result in the product becoming

damaged during operation or the product

becoming unable to operate properly

Handling fuel

1. The engine of the product is designed to

run on a mixed fuel which contains highly

flammable gasoline. Never store cans of fuel

or refill the tank of the unit in any place where

there is a boiler, stove, wood fire, electrical

sparks, welding sparks, or any other source of

heat or fire which might ignite the fuel.

2. Never smoke while operating the unit or

refilling its fuel tank.

When refilling the tank, always turn off the engine

and allow it to cool down. Take a careful look

around to make sure that there are no sparks or

open flames anywhere nearby before refueling.

4. Wipe spilled fuel completely using a dry rag if

any fuel spillage occurs during refueling.

5. After refueling, screw the fuel cap back tightly

onto the fuel tank and then carry the unit to a

spot 10feet (3m) or more away from where it

was refueled before turning on the engine.

Transportation

1. When hand-carrying the product, cover over

the cutting part if necessary, lift up the product

and carry it paying attention to the blade.

2. Never transport the product over rough

roads over long distances by vehicle without

removing all fuel from the fuel tank. If doing so,

fuel might leak from the tank during transport.

2. MACHINE INFORMATION

Intended use

The brush cutter/string trimmer is only intended

for cutting grass, weeds, bush and other such

undergrowth, and should not be used for any

other purpose such as edging or hedge cutting as

this may cause injury.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BCM1022 in the language / languages: English as an attachment in your email.

The manual is 4,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BCM1022 Manual

Product: