763846
6
Zoom out
Zoom in
Previous page
1/88
Next page
EN
6
A contaminated and blocked filter will cause a
reduction in the pressure, which will negatively
influence the performance of the air stapler.

When in use, always wear eye protection
that meets the ANSI specifications, and
offers protection both in front and at the
sides from flying objects when loading,
operating and maintaining the air stapler.
Flying fasteners and splinters can cause
severe injury.
The employer or user must insist that proper eye
protection is worn. Eye protection equipment
should meet the specification of the American
National Standards Institute, ANSI Z87.1-1979
and must offer protection from both the front and
the sides.
Glasses without side shield and face
protector do not offer sufficient protection.

Fig.5
• Disconnect the air hose.
• Release the fastener latch and withdraw this
along the fastener guide unit.
• Insert 1 fastener strip into the magazine.
Load with fastener points upwards.
• Press the fastener guide unit back into the
magazine, and lock the fastener latch.
• Reconnect the air hose to the air stapler.

When in use, always wear eye protection
that meets the ANSI specifications, and
offers protection both in front and at the
sides from flying objects when loading,
operating and maintaining the air stapler.
Flying fasteners and splinters can cause
severe injury.

• Read the general safety instructions and
warnings in these instructions for use
carefully.
• Refer to the specifications earlier in these
instructions for the correct operating
conditions for the air stapler.
Make sure the stapler is lubricated
properly before using it the first time.

Fig.1 - 4
A piston powered by compressed air drives the air
stapler. Illustrations 1 – 4 on page 2 + 3 show how
the air stapler works.


Pressing the trigger activates the air stapler. Every
time the trigger is pressed, the air stapler will drive
a fastener into the workpiece.
Keep your hands well clear of the fastener
head. On no account should you point the
air stapler at any person or animal.



Fig. 6
At the front of the tacker there is a cover with a red
lever.
This cover can be removed when a staple is
blocked into the shaft.
Warning! To avoid injury:
Disconnect the air hose.
First release the fastener latch and
withdraw this along the fastener guide
unit. Removing the cover, while the
system is under pressure, can cause
serious injury: the staples can jump out
of the tacker unit!

• Remove the staples from the guide unit.
• Pull the red lever of the cover (in front of
tacker) downwards and remove the cover.
• The blocked stapler can be removed.
• After mounting the cover, staples and fastener
latch can be placed again.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm ATM1042 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm ATM1042 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info