Manual Ferm AGM1067P (page 8 of 148) (All languages)

764199

Zoom out

Zoom in

1/148

Assembling the protection guard

(Fig. A and B)

• Place the machine on a table with the spindle

(8) facing upwards.

• Place the protection guard (3) over the

machine head as shown in Figure C making

sure the ridges on the protection guard fall into

the notches of the machine head.

• Turn the protection guard counter clockwise

and secure the guard by tightening the screw

(14).

Never attempt to remove the guard.

Mounting and removing the wheel disc

(Fig. B)

• Always use suitable wheel disc for this

machine with diameter Ø 100 / 115 / 125 mm

and a bore from 22 / 22 / 16 mm the thickness

of the wheel disc should be 6 mm for wheel

disc for grinding and 3 mm for wheel disc

for cutting, the mounting wheel disc may not

touch the safety guard.

Mounting

• Place the machine on a table with the

protection guard (3) facing upwards.

• Mount the flange (9) onto the spindle (8).

• Place the wheel disc (10) onto the spindle (8).

• Keep the spindle lock button (1) pressed and

firmly tighten the clamping nut (11) onto the

spindle (8) by using the spanner (12).

Removing

• Place the machine on a table with the

protection guard (3) facing upwards.

• Keep the spindle lock button (1) pressed and

loosen the clamping nut (11) using the spanner

(12).

• Remove the wheel disc (10) from the spindle (8).

• Keep the spindle lock button (1) pressed and

firmly tighten the clamping nut (11) using the

spanner (12).

3. OPERATING

Make sure that the work piece is properly

supported or fixed and keep the supply

cord routing away from the work area.

Switching on and off (Fig. A)

• To switch the machine on, press the On/off

switch (2).

• To switch the machine off, release the On/off

switch (2).

Hold the machine away from the work piece when

turning it on and off because the wheel disc could

damage the work piece.

• Clamp the work piece firmly or use another

method to ensure that it cannot move while

working.

• Check the discs regularly. Worn wheel discs

have a negative effect on the machine’s efficien-

cy. Change to a new wheel disc in good time.

• Always first turn the machine off after use

before removing the plug from the socket.

Deburring (Fig. C)

An angle of inclination of 30º to 40º will give the

best results when deburring. Move the machine

back and forth using light pressure. This will

prevent the work piece from discolouring or

becoming too hot and will avoid making groves.

Never use abrasive cutting discs for

deburring work!

Cutting (Fig. D)

For cutting, a special protection guard must be

used (not included).

Maintain firm contact with the work piece to

prevent vibration and do not tilt or apply pressure

and when cutting. Use moderate pressure when

working, appropriate to the material that is

being worked on. Do not slow down wheel discs

by applying sideways counter pressure. The

direction in which you want to cut is important.

The machine must always work against the

direction of the cut; so never move the machine

in the other direction! There is the risk that the

machine will catch in the cut causing kickback

and that you will lose control.

Hints for optimum use

• Clamp the work piece. Use a clamping device

for small work pieces.

• Hold the machine with both hands.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm AGM1067P in the language / languages: All languages as an attachment in your email.

The manual is 13,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm AGM1067P Manual

Product: