763252

Ferm AGM1066S Manual

10
Zoom out
Zoom in
Previous page
1/176
Next page
10
EN
3. OPERATING
Make sure that the work piece is properly
supported or fixed and keep the supply
cord routing away from the work area.
Switching on and off (Fig. A)
• To switch the machine on, keep the lock-off
button (17) pressed and then press the On/off
switch (5).
• To switch the machine off, release the On/off
switch (5).
Hold the machine away from the work piece when
turning it on and off because the wheel disc could
damage the work piece.
• Clamp the work piece firmly or use another
method to ensure that it cannot move while
working.
• Check the discs regularly. Worn wheel discs
have a negative effect on the machine’s
efficiency. Change to a new wheel disc in good
time.
• Always first turn the machine off after use
before removing the plug from the socket.
Deburring (Fig. E)
An angle of inclination of 30º to 40º will give the
best results when deburring. Move the machine
back and forth using light pressure. This will
prevent the work piece from discolouring or
becoming too hot and will avoid making groves.
Never use abrasive cutting discs for
deburring work!
Cutting (Fig. F)
For cutting, a special closed protection guard (Fig.
D2) must be used (not included).
Maintain firm contact with the work piece to
prevent vibration and do not tilt or apply pressure
and when cutting. Use moderate pressure when
working, appropriate to the material that is
being worked on. Do not slow down wheel discs
by applying sideways counter pressure. The
direction in which you want to cut is important.
The machine must always work against the
direction of the cut; so never move the machine
in the other direction! There is the risk that the
machine will catch in the cut causing kickback
and that you will lose control.
Hints for optimum use
• Clamp the work piece. Use a clamping device
for small work pieces.
• Hold the machine with both hands.
• Switch on the machine.
• Wait until the machine has reached full speed.
• Place the wheel disc on the work piece.
• Slowly move the machine along the work
piece, firmly pressing the wheel disc against
the work piece.
• Do not apply too much pressure on the
machine. Let the machine do the work.
• Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
4. MAINTENANCE
Before cleaning and maintenance, always
switch off the machine and remove the
mains plug from the mains.
Clean the machine casings regularly with a soft
cloth, preferably after each use. Make sure that
the ventilation openings are free of dust and
dirt. Remove very persistent dirt using a soft
cloth moistened with soapsuds. Do not use any
solvents such as gasoline, alcohol, ammonia,
etc. Chemicals such as these will damage the
synthetic components.
Replace power cords
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Mains plug replacement (UK only)
If the moulded 3-pin plug attached to the unit is
damaged and needs replacing, it is important
that it is correctly destroyed and replaced by
an approved BS 1363/7A fused plug and that
the following wiring instructions are followed.
The wires in the mains cable are coloured in
accordance with the following code:
• blue neutral
• brown live
As the colours of the wires in the mains cable
of the unit may not correspond to the coloured
markings identifying the terminals in the plug,
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm AGM1066S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm AGM1066S in the language / languages: All languages as an attachment in your email.

The manual is 14,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info