Manual Ferm AGM1041 (page 9 of 84) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

510077

Zoom out

Zoom in

1/84

Ferm

Cutting

Fig. 6

Maintain firm contact with the workpiece to

prevent vibration and do not tilt or apply pressure

and when cutting. Use moderate pressure when

working, appropriate to the material that is being

worked on. Do not slow down grinding discs

by applying sideways counter pressure. The

direction in which you want to cut is important.

The machine must always work against the

direction of the cut; so never move the machine

in the other direction! There is the risk that the

machine will catch in the cut causing kickback and

that you will lose control.

The ON/OFF/ switch

Fig. 1

Switch ON

Use one finger to push the lock button forward

and then press the switch.

Switch OFF

Release the switch.

The grinder will continue to run after it is

turned off.

Only lay the machine down once the motor

has completely stopped turning. Do not put the

machine on a dusty surface. Dust particles can

penetrate the machine.

Never use the spindle key to stop the

motor turning.

Never use the machine to grind

magnesium workpieces.

5. SERVICE & MAINTENANCE

Make sure that the machine is not live

when carrying out maintenance work on

the motor.

This machine has been designed to operate

over a long period of time with a minimum of

maintenance. Continuous satisfactory operation

depends upon proper machine care and regular

cleaning.

Cleaning

Keep the ventilation slots of the machine clean to

prevent overheating of the engine.

Regularly clean the machine housing with a

soft cloth, preferably after each use. Keep the

ventilation slots free from dust and dirt. If the dirt

does not come off use a soft cloth moistened with

soapy water. Never use solvents such as petrol,

alcohol, ammonia water, etc. These solvents may

damage the plastic parts.

Lubrication

The machine requires no additional lubrication.

Trouble shooting

Below we have listed a few probable causes and

solutions to which you can refer if your circular

saw does not function properly.

1. Machine fails to operate.

• Power turned off.

• (Extension) cable damaged.

2. The elektromotor hardly reaches

maximum speed.

• The extension cable is too thin and/or too

long.

• The mains voltage is lower than 230 V.

3. Machine overheats.

• Air vents are blocked. Clean them with a dry

cloth.

• The machine has been overloaded. Use the

machine for the purpose it is made for.

4. Excessive sparking or elektromotor runs

irregular.

• There’s dirt inside the motor or the carbon

brushes are worn.

• Replace the carbon brushes or bring the

machine to a specialized repair centre.

Faults

Should a fault occur, e.g. after wear of a part,

please contact the service address on the

warranty card. Separately you will find an

exploded view showing the parts that can be

ordered.

Environment

To prevent damage during transport, the

appliance is delivered in a solid packaging which

consists largely of reusable material. Therefore

please make use of options for recycling the

packaging.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm AGM1041 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 2,98 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm AGM1041 Manual

Product: