390340

Ferm agm1029 Manual

8
Zoom out
Zoom in
Previous page
1/136
Next page
8
EN
● Remove the ange (11).
● Remove the guard (5) by loosening the Allen
screw (14) and the nut (15) with the Allen key
(16).
● Mount the ange (13).
● If necessary, mount the grinding disc (12).
● Keep the spindle lock button (3) pressed and
mount the ange (10) using the ange key (9).
Mounting and removing the grinding disc

2
Do not use the machine without the
guard.
Mounting
● Place the machine on a table with the guard (5)
facing upwards.
● Keep the spindle lock button (3) pressed and
remove the ange (10) using the ange key (11).
● Mount the grinding disc (12).
● Keep the spindle lock button (3) pressed and
mount the ange (10) using the ange key (11).
Removing
● Place the machine on a table with the guard (5)
facing upwards.
● Keep the spindle lock button (3) pressed and
remove the ange (10) using the ange key (11).
● Remove the grinding disc (12).
● Keep the spindle lock button (3) pressed and
mount the ange (10) using the ange key (11).

Mounting
● Tighten the auxiliary grip (7) into one of the
mounting holes (17).
Removing
● Loosen the auxiliary grip (7) from the mounting
hole (17).
USE

● To switch on the machine in continuous mode,
keep the lock-off button (2) pressed and press
the on/off switch (1).
● To switch off the machine, press the on/off
switch (1) again.

The main grip can be set to 3 positions.
2
Do not set the main grip during use.
● Slide the release button (8) in the direction of
the main grip (6).
● Turn the main grip (6) to the required position
until it locks into place.
● Release the release button (8).
Hints for optimum use
● Clamp the workpiece. Use a clamping device
for small workpieces.
● Draw a line to dene the direction in which to
guide the grinding disc.
● Hold the machine with both hands.
● Switch on the machine.
● Wait until the machine has reached full speed.
● Place the grinding disc on the workpiece.
● Slowly move the machine along the pre-drawn
line, rmly pressing the grinding disc against
the workpiece.
● Do not apply too much pressure on the
machine. Let the machine do the work.
● Switch off the machine and wait for the
machine to come to a complete standstill
before putting the machine down.
CLEANING AND MAINTENANCE
4
Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
● Regularly clean the housing with a soft cloth.
● Keep the ventilation slots free from dust and
dirt. If necessary, use a soft, moist cloth to
remove dust and dirt from the ventilation slots.

Worn or damaged grinding discs must be
replaced immediately.
2
Only use sharp and undamaged grinding
discs.
● To remove the old grinding disc (12), proceed
as described in the section
″Mounting and removing the grinding disc″.
● To mount the new grinding disc (12), proceed
as described in the section
″Mounting and removing the grinding disc″.
Checking and replacing the carbon brushes

The carbon brushes must be checked regularly.
If the carbon brushes are worn, the machine will
start to run unevenly.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm agm1029 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm agm1029 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Norwegian as an attachment in your email.

The manual is 6,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info