Manual Fender Stage 1000 (page 6 of 20) (English)

443028

Zoom out

Zoom in

1/20

wwwwww

ffeennddeerr..ccoomm

✧

wwwwww

..mmrrggeeaarrhheeaadd..nneett

™™

Your new Stage™ 1000 / 1600 amplifier delivers world–class Fender

tone and world–standard Fender

DSP technology:

• 160W output power @ 4 ohms (100W @ 8 ohms)å

• Seven Timbre filters for total tone control

• Digital Signal Processing

• Simultaneous use of Reverb and effects tone tools -

16 REVERB TYPES and 16 FX SELECTIONS

• Separate LEVEL and FX TIME/RATE controls

• Selectable Normal and Drive channels with independent volume

and tone controls

• Selectable Drive 1 and Drive 2 channels for two independently

adjustable distortion channels.

• Impedance balanced XLR LINE OUT jack

• PRE AMP OUT and POWER AMP IN jacks

• 4-button FOOTSWITCH (included) enables remote activation of: (1)

Channel Select, (2) Drive Select, (3) Effects, (4) Reverb

•

• Built in Tuner

Thank you for choosing Fender

The W

orld’

s most popular instr

ument amplifiers—since 1946

A. INPUT - Plug-in connection for your guitar.

B. VOLUME - Adjusts the loudness of the Normal channel.

C. TREBLE / MIDDLE / BASS - Adjusts the high–, middle– and

low–frequency tone of the Normal channel.

D. CHANNEL SELECT -

OUT Normal channel {B–C}

IN Drive channels {E–J}

E. DRIVE 1 - Adjusts the distortion level of the Drive 1 channel.

F. VOLUME 1 - Adjusts the overall loudness of the Drive 1 channel.

G. DRIVE SELECT - Press CHANNEL SELECT {D} in to activate

DRIVE SELECT.

OUT Drive 1 channel {E–F, J}

IN Drive 2 channel {H–I, J}

H. DRIVE 2 - Adjusts the distortion level of the Drive 2 channel.

I. VOLUME 2 - Adjusts the overall loudness of the Drive 2 channel.

J. TREBLE / MID / BASS - Adjusts the high–, middle– and

low–frequency tone of the Drive channels.

K. TIMBRE - Press repeatedly to select an amp character as indicated

by the LEDs. Your selection is stored and automatically activated for

each channel (Normal, Drive 1, Drive 2).

TIMBRE FILTERS: These pre-set Equalizer curves allow the

Dyna–Touch amps to create seven very different voices on each

channel. FLAT—Preamp and Power Amp signal without further

equalization. BRIGHT—Treble boost, especially effective for

brightening the tone of double–coil pickups. DARK—Treble cut,

especially effective for traditional Jazz tones with the Normal

channel. DEEP—Bass boost, especially effective for beefing up

the tone of single–coil pickups. SCOOP—A severe low–mid

scoop with bass boost designed for modern distortion tones.

SQUAWK—A strong mid peak reminiscent of a partially

depressed Wah–Wah pedal; great for distorted solos that need

to cut through the mix. ACOUSTIC—Simulates the sound of an

acoustic–electric guitar with extreme high treble boost and bass

boost; best with the Normal channel. Note: This much Timbre

flexibility requires that you use a little common sense! It is

possible to get “too much of a good thing,” such as undesirable

treble harshness or bass boominess depending on your

particular guitar, playing style and knob settings.

L. TUNER - Activates the tuner and mutes audio output. Strike a

string and the top row of LEDs indicate the nearest note.

Sharp/flat notes are indicated by two LEDs; for example, A and

B light up to indicate A sharp (B flat). The bottom row of LEDs

indicate fine tuning.

M. REVERB LEVEL - Adjusts the level of the active Reverb.

N. REVERB TYPE - Selects the active Reverb (see next page).

O. EFFECTS LEVEL - Adjusts the level of the active effect.

P. EFFECTS SELECT - Selects the active effect (see next page).

Q. TIME/RATE - Adjusts the interval length / modulation speed of

the active effect (see next page).

Rear Panel

R. POWER SWITCH - Switches the amplifier on / off.

S. POWER CORD SOCKET - Connect the included

power cord in accordance with the voltage and

frequency ratings listed on the rear panel of your

amplifier.

T. PARALLEL SPEAKER OUTPUTS - Connect a single 8Ω

speaker (internal or external) to the MAIN SPKR jack. Connect

an additional 8Ω speaker (internal or external) to the EXT. SPKR

jack. 4Ω minimum total.

Speaker(s) Use Load / Output

One 8Ω speaker MAIN jack 8Ω / 100W

Two 8Ω speakers both jacks 4Ω / 160W

U. LINE OUT - Connect this XLR output

jack to the input of sound reinforcement

or recording equipment.

V. PRE AMP OUT / POWER AMP IN -

Effects Loop - Connect PRE AMP OUT to an effects device input,

then connect the effects device output to PWR AMP IN.

Multiple Amps - Connect the primary unit’s PRE AMP OUT to

the auxiliary unit’s PWR AMP IN. The primary unit is used to

control all auxiliary units.

Recording or Reinforcement - Connect PRE AMP OUT to the

input jack of sound equipment.

Use TS (Tip-Sleeve) standard type plugs with these

jacks. The PRE AMP OUT signal includes onboard tone shaping

and DSP effects processing.

W. FOOTSWITCH - Connect the 4-button Fender footswitch

(included) at this jack to enable remote switching of CHANNEL

SELECT, DRIVE SELECT, EFFECTS and REVERB. When

plugged in, the footswitch buttons override the corresponding

front panel controls.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fender Stage 1000 in the language / languages: English as an attachment in your email.

The manual is 4,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fender Stage 1000 Manual

Product: