607105
5
Zoom out
Zoom in
Previous page
1/7
Next page
LINE OUTPUT JACKS - Signal from each of the chan-
nels are combined with reverb and effects to form the
input to the power amplifier stage. The Line Outs are
wired from this point. The 1/4 Jack (Item P) and the
XLR jack (Item Q) provide easy connection paths from
the KXR 200 to any external devices, such as a slave
amp or a mixer. It is also useful for recording live per-
formances. Note that inserting a plug into one of the
Line Outs jacks does not interrupt the normal internal
signal flow of the KXR 200.
EFFECTS SEND JACK - This jack is the output of the
effects bus, where all the channels Effects Send are
combined. The signal coming out of this jack could be
used to drive an effects device, a slave amp, or as an
input to a mixer . Note that the signal coming out of
this jack is reverb-free.
EFFECTS RETURN JACK - This jack inputs signal to the
master section of the KXR 200 through the Effects
Return control (Item J). This jack can be used with the
Effects Send Jack (item R) as a patch point for mono
effect devices. This jack can also be used as the input
jack when the KXR 200 is used as a slave amp.
CHANNEL INSERT JACKS - These jacks are wired
post-EQ and post channel volume control. By inserting
an external signal source into one of these jacks,
through a stereo jack wired to the tip and sleeve (with
the ring left floating), the appropriate channel’s EQ
and volume control are bypassed. By shorting the tip
of the inserting jack to its ring, the channel’s signal
and the externally input signal could be mixed togeth-
er. The channel inserts can also serve as effects loop
points by using a stereo jack wired tip=effects send,
and ring=effects return. Note that the layout of the
insert jacks on the back panel is the mirror image of
the channels layout on the front panel.
POWER CORD - This amplifier is equipped with a
grounding type supply cord to reduce the possibility of
shock hazard. Be sure to connect it to a grounded AC
receptacle. The line cord should be connected to a
suitable power source, in accordance with the voltage
and frequency as shown by the power rating on the
rear panel. DO NOT ALTER THE AC (MAINS) PLUG.
NOTE: DO NOT BLOCK THE AIR FLOW TO THE
REAR PANEL; FOR EXAMPLE, BY BACKING THE
AMPLIFIER UP AGAINST A WALL. The rear panel
contains a heatsink that needs air flow to cool off the
amplifier. Blocking the air flow may result in equip-
ment failure due to excessive heat building up inside
the chassis.
WARNING : THIS EQUIPMENT MUST BE EARTH
GROUNDED.
COVERING CARE - UNPLUG THE POWER CORD
BEFORE CLEANING - The exclusive vinyl covering on
your cabinet has been especially designed for years of
lasting beauty. A very light, soapy solution on a
sponge may be used to remove dirt and residue that
may accumulate in the texture. Be careful as not to let
any liquid get inside the chassis or contact the operat-
ing surfaces.
P,Q.
R.
S.
T.
KXR 200 REAR PANEL
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fender KXR 200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fender KXR 200 in the language / languages: English as an attachment in your email.

The manual is 0,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info