442906
5
Zoom out
Zoom in
Previous page
1/16
Next page
5
POWER RATING
260 WATTS
FUSE
POWER STANDBY
SPEAKER EXT.
SPEAKER
FOOT
PEDAL
A. POWER RATING - Connect the power line cord to a
g rounded AC receptacle in accordance with the
voltage and frequency ratings shown on the Rear Panel
of the amplifier.
B. FUSE - Protects the amplifier from electrical faults.
Replace fuse only with same type and rating listed on
the fuse holder. If the amplifier repeatedly blows fuses,
take the amplifier to an authorized Fender Service
Center.
C . POWER SWITCH - Push UP to switch ON the amplifier.
Push DOWN to switch OFF the amplifier.
D. STANDBY SWITCH - Push DOWN to put the amplifier
into STANDBY mode. Push UP to put the amplifier into
normal OPERATING mode. In STANDBY mode, power
is supplied to the tube filaments only. This eliminates
w a rm-up time when re t u r ning the amplifier to
OPERATING mode and also increases tube life span.
The POWER switch {C} must be ON for the STANDBY
switch to function.
E. MAIN SPEAKER JACK - Plug-in connection for
speakers. A speaker must always be connected at this
jack when the amplifier is ON.
F. EXTERNAL SPEAKER JACK - Plug-in connection for
an external speaker. This jack is wired in parallel with
the MAIN SPEAKER JACK {E}. A total speaker
impedance load of 4-ohms should be used to avoid
damage to the amplifier.
G. FOOTSWITCH JACK - Plug-in connection for the
FOOTSWITCH which enables ON/OFF switching of the
VIBRATO and REVERB effects. The VIBRATO effect
will not function without the FOOTSWITCH plugged in.
TYPE: PR 186
PART NUMBE R : 021-7370-000 (100V, 50/60Hz) Japan, 021-7300-000 (120V, 60Hz) USA, 021-7360-000 (230V, 50Hz) Euro,
021-7340-000 (230V, 50Hz) UK, 021-7330-000 (240V, 50Hz) A u s t r a l i a .
POWER REQUIREMENTS: 260 watts
POWER OUTPUT: 85 watts R.M.S.
IMPEDANCES: INPUTS 1: 1M ohm (both channels), INPUTS 2: 136k ohms (both channels)
OUTPUT: 4 ohms (both speaker jacks together)
FUSE TYPE: 4 ampere, slow-blow, 125 volt minimum
SPEAKER COMPLEMENT: Two 12-inch Fender vintage re-issue Special Design speakers (P/N-037617)
TUBE COMPLEMENT: OUTPUT: Four Fender Special Design 6L6GC’s (P/N-039214),
PRE-AMP: Four Fender Special Design 12AX7As (P/N-013341),
Two Fender Special Design 12AT7’s (P/N-023531)
FEATURES: Vibrato and Reverb, Tilt-back legs
DIMENSIONS: HEIGHT: 19-7/8 in. (49.2 cm)
WIDTH: 26-5/32 in. (63.5 cm)
DEPTH: 10-3/8 in. (21.9 cm)
WEIGHT: 64 lbs. (29 kg)
Product specifications are subject to change without notice.
`65 Twin Reverb – Rear Panel
The tube BALANCE and BIAS of your ‘65 Twin Reverb is adjusted at the factory and should
provide years of service before needing attention. If the sound quality of the amp has degraded
noticeably and HUM BALANCE and BIAS adjustments fail to restore sound quality, the tubes
are worn and need replacement. Note that pre-amplifier tubes last longer than output tubes. If
you are not sure about the condition of your tubes or the following procedures, take your
amplifier to an authorized Fender Service Center.
A. HUM BALANCE ADJUSTMENT - This adjustment minimizes the hum heard at the speakers
due to tube filament imbalance. Balance is usually adjusted only when tubes have been
replaced. •Adjustment Instructions: Turn the amplifier ON for 2 minutes with nothing
plugged into any of the INPUTS. Rotate the VIBRATO CHANNEL volume, middle, and bass
knobs fully clockwise and the treble knob fully counter-clockwise. Rotate ALL of the
NORMALCHANNEL knobs fully counter-clockwise. Switch OFF the REVERB and VIBRATO
effects. Then insert a slotted screwdriver into the BALANCE ADJUSTMENT control, (see
“A” in FIG. 1) and rotate back and forth to the position with the least amount of hum.
B . BIAS ADJUSTMENT - This adjustment only should be made if the output tubes are
replaced with tubes not identical to the original tubes and should be adjusted only by an
authorized Fender Service Center.
Tube Adjustments
Specifications
Replace tubes with identical F e n d e r® original equipment only (see SPECIFICATIONS below). Tube location is printed on the tube label, inside the cabinet.
FIG. 1
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fender 65 Twin Reverb at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fender 65 Twin Reverb in the language / languages: English as an attachment in your email.

The manual is 0,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info