442898

Fender 65 Deluxe reverb Manual

7
Zoom out
Zoom in
Previous page
1/20
Next page
7
A. FUSE - Protects the amplifier from electrical faults.
Replace fuse only with same type and rating as listed
on the fuse holder. If the amplifier repeatedly blows
fuses, take the amplifier to an authorized Fender
Service Center.
B. POWER RATING - Connect the power line cord to a
grounded AC receptacle in accordance with the voltage
and frequency ratings shown on the Rear Panel of your
amplifier.
C. POWER - Push UP to switch ON the amplifier. Push
DOWN to switch OFF the amplifier.
D. STANDBY - Push DOWN to put the amplifier into
STANDBY mode. Push UP to put the amplifier into
normal OPERATING mode. In STANDBY mode power is
supplied to the tube filaments only. This eliminates
warm-up time when returning the amplifier to
OPERATING mode after
short breaks and also extends
tube life. The POWER {C}
switch must be ON for the
STANDBY switch to function.
E. INTERNAL SPEAKER JACK - Plug-in connection for
the 8Ω internal speaker. A speaker must always be
connected at this jack when the amplifier is ON. A
speaker impedance load of 8Ω should be used to avoid
distortion or damage to the amplifier.
F. EXTERNAL SPEAKER JACK - Plug-in connection for
an external speaker. This jack is wired in parallel with
the INTERNAL SPEAKER JACK {E} and affects the
speaker impedance load.
G. FOOTSWITCH JACK - Plug-in connection for the
FOOTSWITCH which enables ON/OFF switching of the
VIBRATO and REVERB effects. The VIBRATO effect
will not function without the FOOTSWITCH plugged in.
TYPE: PR 239
PART NUMBERS: 021-7470-000 (100V, 50/60Hz) JPN 021-7400-000 (120V, 60Hz) US
021-7460-000 (230V, 50Hz) EUR 021-7440-000 (230V, 50Hz) UK
021-7430-000 (240V, 50Hz) AUS
POWER: INPUT: 100W (AC line cord) OUTPUT: 22W at 8Ω (speaker jacks)
IMPEDANCES: INPUTS 1: 1MΩ (both channels) INPUTS 2: 136kΩ (both channels)
OUTPUT: 8Ω (both speaker jacks combined)
FUSE TYPE: 2A, 125V (100-120V versions) F1A, 250V (230-240V versions)
SPEAKER COMPLEMENT: 12-inch, 8Ω, Jensen C12K (P/N-057146)
TUBE COMPLEMENT: One Fender Special Design 5AR4 (P/N-041400)
Two Fender Special Design 6V6GT’s (P/N-023564)
Four Fender Special Design 12AX7A’s (P/N-013341)
Two Fender Special Design 12AT7’s (P/N-023531)
DIMENSIONS: HEIGHT: 17-1/2 in (44.5 cm)
WIDTH: 24-1/2 in (62.2 cm)
DEPTH: 9-1/2 in (24.1 cm)
WEIGHT: 42 lb (19.1 kg)
Product specifications are subject to change without notice.
`65 Deluxe Reverb – Rear Panel
The tube bias and balance adjustments on your ‘65 Deluxe Reverb are factory adjusted and
should provide years of service before needing attention. If the sound quality of the amp has
degraded noticeably, the tubes, may be worn and some, usually the output tubes, may need
replacement. If you are unsure about the condition of your tubes, take your amplifier to an
authorized Fender Service Center. Replace tubes with Fender
®
original equipment only (see
SPECIFICATIONS below). Tube location is printed on the tube label inside the cabinet.
Tube Replacement
Specifications
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fender 65 Deluxe reverb at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fender 65 Deluxe reverb in the language / languages: English as an attachment in your email.

The manual is 2,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info