TYPE: PR 401 PR 400 PR 453
PART NUMBER: 22-6700 (120V, 60Hz) US 22-6800 (120V, 60Hz) US 22-6900 (120V, 60Hz) US
22-6730 (240V, 50Hz) Aust 22-6830 (240V, 50Hz) Aust 22-6930 (240V, 50Hz) Aust
22-6740 (230V, 50Hz) UK 22-6840 (230V, 50Hz) UK 22-6940 (230V, 50Hz) UK
22-6760 (230V, 50Hz) Eur 22-6860 (230V, 50Hz) Eur 22-6960 (230V, 50Hz) Eur
22-6770 (100V, 50/60Hz) Jpn 22-6870 (100V, 50/60Hz) Jpn 22-6970 (100V, 50/60Hz) Jpn
POWER REQUIREMENTS: 400W 400W 400W
POWER OUTPUT: 100W RMS into 8Ω @ 5%THD 160W RMS into 4Ω @ 5%THD 100W RMS into 8Ω @ 5%THD
(WITH EXTENSION SPEAKER): 160W RMS into 4Ω @ 5%THD N/A 160W RMS into 4Ω @ 5%THD
INPUT IMPEDANCE: INPUT 1: 850kΩ, INPUT 2: 66kΩ INPUT1: 850kΩ, INPUT 2: 66kΩ INPUT1: 850kΩ, INPUT 2: 66kΩ
FX SEND OUTPUTIMPEDANCE: 1kΩ 1kΩ 1kΩ
FX RETURN INPUT IMPEDANCE: 10kΩ 10kΩ 10kΩ
POWER AMPIN SENSITIVITY: 810mV for 160W into 4Ω @1kHz 810mV for 160W into 4Ω @1kHz 810mV for 160W into 4Ω @1kHz
620mV for 100W into 8Ω @1kHz N/A 620mV for 100W into 8Ω @1kHz
FUSE: 4A125V for 100V / 120V ver 4A125V for 100V /120V ver 4A125V for 100V /120V ver
2A250V for 230V / 240V ver 2A250V for 230V / 240V ver 2A250V for 230V / 240V ver
FOOTSWITCH: 2 Button - (P/N 050419) 2 Button - (P/N 050419) 2 Button - (P/N 050419)
Normal/Drive, Drive/More Drive Normal/Drive, Drive/More Drive Normal/Drive, Drive/More Drive
SPEAKER COMPLIMENT: One 8Ω Celestion G12T-100 Two 8Ω Celestion G12T-100 N/A
12” speaker (P/N 054420) 12” speakers (P/N 054420)
DIMENSIONS: HEIGHT: 17.5 in. (45 cm) 18.5 in. (47 cm) 8.5 in. (22 cm)
WIDTH: 22.4 in. (57 cm) 26.1 in. (66 cm) 22.4 in. (57 cm)
DEPTH: 10.2 in. (26 cm) 10.3 in. (26 cm) 9.5 in. (24 cm)
WEIGHT: 42 lbs. (19.1 kg) 53 lbs. (24.1kg) 24 lbs. (10.9 kg)
Product specifications are subject to change without notice.
5
1 . POWER SWITCH - Tu r ns the AC power ON and OFF.
2. LINE CORD - This amplifier is equipped with an
IEC grounding type supply cord to reduce the
possibility of shock hazard. Be sure to connect it
to a grounded AC receptacle in accordance with
the voltage and frequency ratings listed on the
rear panel under INPUT POWER.
• NOTE: Items 3 and 4 apply only to the
Stage 100H.
3. SPEAKER OUTPUT (8Ω minimum) - Use this out-
put jack when only one 8Ω speaker enclosure is to
be connected to the Stage 100H. If two 8Ω
speaker enclosures are to be connected, use both
parallel speaker output jacks (total load of 4Ω).
4 . SPEAKER OUTPUT (4Ω minimum) - Use this output
jack when o n e 4Ω speaker enclosure is to be con-
nected to the Stage 100H. (Using this jack inter-
nally switches the Stage 100H to accept a 4Ω load.)
• NOTE: Item 5 applies only to the Stage 100.
5. EXTERNAL SPEAKER (8Ω minimum) - Use this
output jack when one 8Ω speaker enclosure is to
be connected to the Stage 100 for additional out-
put. The Stage 100’s internal speaker must be
connected while using this jack.
6. LINE OUT - This balanced XLR line-level output is
designed for connection to an external power
amplifier or main house mixer. The signal from
this output jack includes all tone shaping done by
the amplifier.
7. RETURN - This 1/4 inch, unbalanced, TS, line-
level input jack is designed to accept a signal
from external effects devices or another amplifier
in a “daisy-chain” configuration.
8. SEND - This 1/4 inch, unbalanced, TS, line-level
output jack is designed to feed the preamp signal
to external effects devices or to an “add-on”
amplifier in a daisy-chain configuration.
9 . FOOTSWITCH - Connect the footswitch at this jack.
The two-button footswitch enables switching
between Normal and Drive channels and ON/OFF
switching of the MORE DRIVE p r e-amplifier boost.
Using this jack disables these switching functions
f r om the front panel. NOTE: Connecting the
footswitch with an unshielded speaker type cord is
p referable to using a shielded coaxial guitar cord .
R
R
e
e
a
a
r
r
P
P
a
a
n
n
e
e
l
l
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
