Manual Felisatti SG6 (page 4 of 36) (English, German, French, Italian, Portuguese, Turkish, Spanish, Finnish)

502485

Zoom out

Zoom in

1/36

BEFORE USING THIS TOOL

Before using the tool, make sure the mains voltage is

correct: it must be the same as that on the specifica-

tion label.

DISCS AND WHEELS

WARNING! For safety reasons always disconnect the

machine from the mains before changing the grinding

wheel.

The discs and wheels must be protected from bangs and

knocks.

Before starting up the machine, check that the grinding

wheel is securely clamped (see Fig. 2).

Warning! Use protective goggles while working.

Do not use wheels of a larger diameter than that shown

on the specifications plate.

The centrifugal force tends to break the grinding wheel

as its speed increases. Said centrifugal force increases

proportionately to the square of the peripheral speed,

thus, for example, while the increase in the speed of a

wheel in going from 30 m/s to 35 m/s is 17%, the in-

crease in the centrifugal force is 36%.

Owing to the many different shapes of grinding wheels

with shank, the type of bonding and the degree of

hardness, no exact diameter capacity can be given.

For example, a cylindrical wheel of diameter 25 and

height 19, with ceramic bonding, allows a speed of

35,100 r.p.m. yet the same diameter with height 50 only

allows a maximum speed of 15,900 r.p.m. The values

shown in table 1 are approximate for general operations.

For special applications it is always best to consult the

manufacturer. It is advisable to insert the shank as far as

possible inside the clamp in order to avoid any bending

or possible vibrating of the grinding wheel.

MOUNTING GRINDING DISCS AND WHEELS

WARNING! For safety reasons, the machine should

always be unplugged from the mains before changing

the disc or wheel.

To mount the grinding wheel, insert the clip into the ma-

chine’s clip-holder shaft, insert the grinding wheel with the

shaft in the clip and turn the nut with a 17-mm spanner,

while holding the nut in place with a 13-mm spanner.

The grinding wheel is dismounted by carrying out this

procedure in reverse order.

PRECAUTION: the clip securing nut must not be

tightened unless a grinding wheel has been inserted

into the clip.

Protect discs and wheels from knocks and blows.

STARTING THE TOOL

WARNING! Check that the mains voltage is the same as

that in the machine’s specifications.

Plug the machine in with the switch off.

Start the machine by turning the switch to position 1

("ON"). To switch off, do the same in reverse.

Speed adjustments (Mod. SG6/1000CE)

The built-in module permits:

- Soft start.

- The maintenance of a practically constant rated speed

up to rated power.

The control electronics allow continuous pre-setting of

the revolutions to adapt the machine to the type of

material to be worked on. Adjustment is made using the

speed adjustment switch C, which has 6 positions to

regulate the speed.

SPECIFICATIONS AND APPLICATIONS OF TABLE 1

Grinding wheel (A)

Abrasive:

Corundum: suitable for steels and steel alloys.

Silicon carbide: cast iron, light metals, hard metal, buil-

ding materials.

Hardness:

Soft: hard materials, smooth surfaces, more intense

roughing, fine polishing.

Hard: soft materials, rough, sharp surfaces, less intense

and longer lasting roughing, high quality surface.

Hard Metal Milling Cutter (B)

Rough toothing: stainless steel, steel alloys, light metals.

Fine toothing: hard steels, hardened steels.

Felt Wheels (C)

These require paste for polishing.

Valve grinding, shiny finishing of ground or polished

surfaces.

Fans (D)

Dies and moulds and light deburring work.

Wire Brush (E)

Steel wire: for cleaning rusty surfaces.

Brass wire: for matt surfaces.

Stainless steel wire: for stainless steel items.

ACCESSORIES

Accessories and their corresponding order number can

be found in our catalogues.

MAINTENANCE AND CARE

WARNING! Always unplug the machine before carrying

out work on it.

- Inspect the tool: Using a worn deburring or cutting

tool will diminish the efficiency of the work and could

damage the motor.

- Inspect the mounting screws: Regularly inspect all

the mounting screws and ensure they are firmly tighte-

ned. Should any screw be loose, tighten it immedia-

tely. Failure to do so could put you at serious risk.

- Motor maintenance: Always take the greatest care

over this and make sure that the motor winding is not

damaged and does not become wet with oil or water.

- The vents should always be kept clean and free of

obstacles.

- Clean the machine thoroughly after each use. Blast the

motor regularly with compressed air.

- Check that the mains lead is in good condition. If it is

not, take it to an Official Service Centre to have it

replaced.

- Brush replacement: The brushes should be replaced

after 150 - 200 hours use or when they are less than

10 mm long. Have this done by an Official Service

Centre. We recommend that at every second change

of brushes, you take the machine to one of our Official

Service Centres for general cleaning and oiling.

- Use only Felisatti accessories and spares. Parts the

changing of which is not covered in this instruction

manual, should be replaced in a Felisatti Official Ser-

vice Centre.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti SG6 in the language / languages: English, German, French, Italian, Portuguese, Turkish, Spanish, Finnish as an attachment in your email.

The manual is 2,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti SG6 Manual

Product: