502467

Felisatti SDF8 Manual

4
Zoom out
Zoom in
Previous page
1/28
Next page
4
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at hand to
use when carrying out maintenance on the indicated parts.
If the tool is used with care and normal maintenance is carried
out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION(Seegures)
AScrewdriverplate(Fig.1)
BLimitofscrewdepth(Fig.1)
CAdjustmentcylinder(Fig.1)
DBeltclip(Fig.1)
ECoolingvent(Fig.1)
FReverseswitch(Fig.1)
GOn/Offswitch(Fig.1)
HLockingbutton(Fig.1)
IElectronicspeedregulationcontrol(Fig.1)
EQUIPMENT
- Operating instructions
- Safety instructions
- Warranty
BEFORE USING THIS TOOL
Before using the tool, make sure the mains voltage is correct:
it must be the same as that on the specication label.
Machines with 230V can also be connected to a 220-V mains
supply.
Before plugging in the tool, always make sure the control
triggerswitchGworksproperlyandreturnstothe(“OFF”)
position when released.
STARTING THE TOOL
WARNING! Check that the mains voltage is the same as that
inthemachine’sspecications.
Plug the machine in with the switch off. Press switch button G
to start the machine and release to stop.
For continuous action, press the switch G and block with
button H.
The machine can be stopped again by pressing and releasing
button G.
Locking the switch is not advisable for precision work.
Electronic speed regulation
These models include the On/Off switch G, a speed regulator
I which permits selection of the speed most
suitableforthespecicjob.
TherequiredspeedisobtainedusingspeedregulatorI,to
the left and right as applicable.
Electronic regulation can be carried out with the machine
running.
Changing direction of rotation left/right.
Select direction of rotation with reversing lever F.
Due to a locking mechanism, the reversing switch F can only
be switched when the On-/off switch G is not depressed. Only
activate the F commutation switch with the machine turned
off.
Setting the depth gauge
TheCadjustmentbushinghas8positions(0.2mm/turn)that
allow the choice of screw depth based on the screw head.
Set the C adjustment bushing all the way forward, until
it stops. Set the screw depth by turning the C adjustment
bushing:
To the right = more screw depth.
To the left = less screw depth.
Next, turn the C adjustment bushing all the way back.
The best way to adjust correctly is make a trial screw hole.
The screw is held in place with a universal magnetic
support.
Presstheendofthescrewrmlyagainstthematerialtobe
screwed until the B depth limit and the screwdriver sheet
disconnect.
To loosen screws, move the F lever to the L position, move it
to the left and remove the B screw depth by tilting it forward.
CHANGING THE PLATE
To change the screwdriver plate A, remove the B screw depth
by tilting it forward.
The pre-selection of the screw depth will be changed and you
will have to readjust the limit.
TECHNICAL DATA
Screwdriver SDF8/700ER
Input power W 701
No-load speed /min 0-4000
Electronic / Reversible Yes
Tool holder capacity inner hexagon mm 6,35
Max. diameter of the screw mm 6
Torquespeed Nm 11
Acoustic pressure dB(A) 82
Sound-power level dB(A) 95
Vibration acceleration m/s² 2,7
Weightaccording EPTA - Procedure 01/2003 Kg 1,82
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti SDF8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti SDF8 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info