500412
5
Zoom out
Zoom in
Previous page
1/28
Next page
5
DESCRIPTION
1. Collet
2. LED worklight (SDF3.6R)
3. Switch (Forward/Reverse)
4. Stick/Pistol selection button (SDF4.8R)
5. Input jack
6. Charger
7. Charge indicator light
8. To rotate into pistol position (SDF4.8R)
9. To rotate into stick position (SDF4.8R)
APPLICATIONS
You may use this product for driving screw with screw
driver bits.
CHARGING SCREW DRIVER (Fig. 1)
This tool has been shipped in low charge condition to prevent
possible problems. Therefore, you should charge it overnight
prior to use.
Note: Batteries will not reach full charge the  rst time
they are charged. Allow several cycles (driving followed by
recharging) for them to become fully charged.
Note: Only use the charger provided.
Connect charger to the tool by inserting charger plug into
input jack. Make sure the power supply is normal household
voltage, 230V, 50Hz, AC only.
■ Connect charger to power supply.
■ The charge indicator light (LED) will light up when charger
is properly connected power supply.
After normal usage, a minimum charge time of 3-5 hours is
required to recharge a completely discharged battery.
The charger housing and the tool handle will become
slightly warm to the touch while charging.
This is normal and does not indicate a problem.
DO NOT operate driver while it is connected to the charger.
The driving ability will not increase.
■ DO NOT place charger in an area of extreme heat of cold.
It works best at normal room temperature.
STICK/PISTOL SELECTION (SDF4.8R)
■ To press selection button at pivot location.
■ Change pistol/stick position by rotating the handle.
ADJUSTING TORQUE (SDF4.8R)
There are twelve torque indicator settings located on the front
of the screwdriver.
■ Rotate adjustment ring to desired setting, aligning num ber
on adjustment ring with arrow on housing.
1 - 2 For driving small screws
3 - 4 For driving screws into soft material
5 - 7 For driving screws into soft and hard materials
8 - 9 For driving screws into hard wood
SWITCH ( FORWARD/REVERSE)
To drive for forward motion, depress the upper part of
switch trigger.
To drive for reverse motion, depress the lower part of
switch trigger.
LED WORKLIGHT (SDF3.6R)
The screwdriver has a built-in LED worklight. This feature
is convenient when working in close or tight areas where
additional light is needed. Whenever the switch trigger is
depressed, the LED worklight will illuminate.
Note: During normal operation, if the LED worklight will not
illuminate, charge the screwdriver.
The LED worklight will be off during Jam and Stall status.
TECHNICAL DATA
Model SDF4.8R SDF3.6R
Motor Volts DC 4.8 3.6
Collet mm 6.35
No Load Speed r/min (RPM) 200 200
Switch Forward and Reverse
Torque Nm max 3.4 3.5
Weight(Include battery) according EPTA - Procedure
01/2003 Kg
0.6 0.4
Charger electrical characteristics
Input V-AC Hz 220 - 50
Output V-DC mA 6-250 4.8-500
Charge Time hours 5 3
Voltage V 4.8 3.6
Battery capacity Ah 1.1 1.3
Batttery type Ni-Cd Li-ion
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti SDF4.8R at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti SDF4.8R in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info