502496

Felisatti SCF190 Manual

6
Zoom out
Zoom in
Previous page
1/40
Next page
6
on the xed guard of the machine indicates the cutting
direction of the teeth).
SETTINGS
1. Cutting depth setting
For a clean perfect cut, the cutting depth should be adjusted
to the thickness of the wood to be worked on, so that the saw
blade protrudes a tooth’s height from the material.
To adjust the cutting depth, loosen the wing nut G and move
the machine upwards or downwards. The scale printed on
the parallel guide indicates the cutting depth.
2. Cutting angle setting
It can cut vertically and with an inclination of up to 45º. The
angle is adjusted by loosening the wing nut M and according
the scale printed on the base.
3. Riving knife adjustment
WARNING: The riving knife F prevents the blade from seizing
up duriing cutting operations and shold alwyas be used for
safety reasons.
The machine is supplied with the riving knife adjusted. When
tting a new blade, follow the steps below for readjustment:
1. Raise the mobile guard C and loosen rhe screw button
B.
2. Move the wedge through the slot to a distance from the
teeth tip and a cutting depth from same of 2 to 3 mm (máx. 5
mm).
3. Tighten the screw B and the machine is ready to work.
4. Lateral stop adjustment
For parallel cutting, use the lateral stop I.
Cutting width is adjusted with the scale or according to the
plotting.
Tighten the wing nut H to work with the lateral stop.
DUST EXTRACTION
WARNING! Always make sure that the tool is switched off
and unplugged before tting or removing any dust extraction
device.
Dust extraction keeps the workplace clean, prevents dust
build-up in the air and facilitates waste elimination.
These saws are equipped with a dust extraction hole N
to which an adapter can be tted (suppied as an optional
accessory).
A universal vacuum cleaner may be tted or any dust
extraction device.
CAUTION: Always use a vacuum extractor designed in
accordance with the applicable Guidelines on sawdust
emission. The exible hoses of conventional vacuum
cleaners t directly onto the dust extraction nozzle.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying out
work on it.
- Checking the saw blade: Deposits of resin and glue on
the saw blade cause inefcient cutting. To avoid them, always
clean the blade immediately after use.
- Inspect the mounting screws: Regularly inspect all
the mounting screws and ensure they are rmly tightened.
Should any screw be loose, tighten it immediately. Failure to
do so could put you at serious risk.
- Motor maintenance: Always take the greatest care over
this and make sure that the motor winding is not damaged
and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is not,
take it to an Ofcial Service Centre to have it replaced.
- Brush replacement: Brushes must be replaced when
length reaches 8 mm or less. To do so, please contact an
authorized after sales service center. We recommend that
every other time you take a tool to an after sales service
center for carbon brushes replacement you also order a
general maintenance (cleaning and lubrication).
Use only Felisatti accessories and spares. Parts the changing
of which is not covered in this instruction manual, should be
replaced in a Felisatti Ofcial Service Centre (See Warranty/
Ofcial Service Centre address leaet).
WARRANTY
See general warranty conditions printed on the attached
sheet.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise to a
minimum. However, in spite of this, in certain circumstances
the maximum noise level in the place of work could exceed 85
dBA. In this case, the operator should wear ear protection.
The machine’s noise and vibration levels, measured in
compliance with EN 50144, usually reach:
Acoustic pressure = 96 dB(A)
Sound-power level = 109 dB(A)
Use ear protection!
Vibration acceleration = 2.7 m/s
2
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti SCF190 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti SCF190 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,92 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info