502473

Felisatti RHF30 Manual

4
Zoom out
Zoom in
Previous page
1/32
Next page
4
Follow very carefully the instructions in this manual, save it
and keep close at hand, ready to carry out any inspection of
parts that may be necessary.
If the machine is used carefully and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See gures)
A SDS-plus chuck (Fig.1)
B Chuck sliding ring (Fig.1)
C Speed regulating handwheel (Fig.1)
D Push button for mode change (Fig.1)
E Mode changeover(Fig.1)
F Label for reversing rotation R-L (Fig.1)
G Changeover left/right direction switch (Fig.1)
H On-/off switch (Fig.1)
I Locking button (Fig.1)
K Depth stop xing wing nut (Fig.1)
L Depth gauge (Fig.1)
M Auxiliary handle (Fig.1)
N Screwdriver bit (accessory*) (Fig.2)
O Key chuck (accessory*) (Fig.2)
P SDS-plus adapter (accessory*) (Fig.2)
* Not included in standard equipment, available as an
accessory
BRIEF DESCRIPTION
A percussion unit generates the power necessary for hammer
drilling or chiselling in masonry.
Just like when we hit a conventional chisel with hammer, a free
piston strikes the bit or chisel, which can move lengthways,
through an intermediate part. This free piston is driven by
a second piston activated by an electric motor through an
air cushion. This electro-pneumatic principle offers great
percussion elasticity and work free from recoil.
Unlike a normal hammer drill, the drilling capacity does not
depend on the pressure exerted on the machine.
Use of the tool: The rotary hammer can be used for hammer
drilling and drilling in wood, metal as well as plastic, and also
for driving screws with driving bits installed in a key chuck
with the SDS-plus adapter. Any other use not mentioned is
TECHNICAL DATA
not allowed.
Additional features of the rotary hammer:
- The machine is equipped with a safety clutch or mechanism
which operates when a bit seizes up, pro-tecting the user
and the machine’s electro-mechanical parts. The clutch is
released automatically.
Warning! This machine must not be used with hole saws, core
bits, diamond bits, etc, as they tend to jam in the hole easily.
This would cause the safety clutch to trip out too often.
- Percussion drill chuck A with SDS–plus mounting for using
tools with SDS-plus shaft. A geared drill chuck or a keyless
chuck can be used in conjunction with the SDS-Plus Adapter
P.
- Change direction of rotation with switch lever G –due to a
lockout mechanism, switching the lever is only possi-ble if the
On/off switch H is not depressed.
- Electronic control of spindle speed, innitely variable by
nger pressure on the On/off switch H.
- For maximum speed regulation use handwheel C.
- For continuous operation the On-/Off switch can be locked
in the “On” position by the button I.
- Auxiliary handle M, adjustable, with integral depth gauge L.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for instance,
using a metal detector, that there are no electric wires or gas
or water pipes under the surfaces you wish to work on.
Make sure the mains voltage is correct: it must be the same
as that on the specication label. Machines with 230V can
also be connected to a 220-V mains supply.
To turn the machine on, press the ON/OFF switch H and keep
it pressed down.
When the ON/OFF switch is released, the machine stops.
WARNING! Always disconnect the plug from the socket
before doing any work on the machine.
1. Fitting the working tools
Hammer drill (Fig.1)
Only use tools with SDS-plus shaft!
1. Clean and grease the shaft of the tool.
2. Before inserting the tool, move the sliding ring B back.
Now the SDS-plus chuck is open.
3. Push the tool in, turn it slightly until it can be pushed in
all the way and you can feel it notch into place.
4. Release the sliding ring B. Now the tool is locked.
5. Check that the tool is properly locked into place. It must
be possible to move it about 10 mm lengthways.
6. Switch machine over to hammer drilling with lever E in
appropriate position.
SDS-plus adapter for geared drill chuck (Fig.3)
Rotary hammer RHF 24/700ERT RHF 30/900ERT
Rated power
W 720 900
No load speed
/min 0-1240 0-1050
No load hammer rate
min 0-5080 0-5100
Drilling diameter in concrete
mm 24 30
Drilling diameter in steel
mm 13 13
Drilling diameter in wood
mm 24 30
Weight according EPTA-Procedure 01/2003 kg 2,6 3,0
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti RHF30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti RHF30 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info