Manual Felisatti NTF250 (page 10 of 52) (English, German, French, Italian, Spanish)

502511

Zoom out

Zoom in

1/52

support and prevent the blade from coming into

contact with the turntable.

WARNING! After this operation has been comp-leted,

make sure that the blade has not come into contact

with the turntable and that the self-locking nut is

tightly screwed down.

5.3 REGULATION OF THE SPLITTING WEDGE

(g. 13)

WARNING! The splitting wedge must never be

thicker than the width blade cutting width and never

thinner than the blade body.

When using the upper table, the splitting wedge

prevents the stopping of the blade caused by the

excessive pressure of the surfaces during cutting.

Whenever such regulation is necessary, proceed as

follows:

- Remove the upper protective casing over the

blade unit.

- Remove the upper table.

- Using a 10 mm Allen wrench, unscrew the

hexagonal head screw A (g.13).

- Adjust the splitting wedge until it stands approx. 5

mm `from the blade and 5 mm lower than the blade.

- Tighten all the screws again and lower the

protective casing.

5.4 REGULATION OF THE BLADE UNIT

COMPARED TO THE WORK SURFACE

90° regulation

- Lower the head of the machine and lock it in place

using the corresponding pin F (g. 1).

- Position the square A as shown in gure 14-b and

adjust the squaring using the dowel C (g. 12).

5.5 REGULATION OF THE TURNTABLE (g. 14)

0° regulation

- Lower the head of the machine and lock it in place

using the corresponding pin F (g. 1).

- Position the turntable on “0”.

- Unscrew the support screws.

- Position the square A between the blade and

support

as shown in the gure.

- Keeping the turntable positioned on “0”, adjust the

support using the corresponding dowels C until a

reading of 90° is shown on the square.

- Tighten all the support screws unscrewed

previously.

5.6 REGULATION OF VERTICAL SURFACE

STROKE END (0° - 45°) (g. 15)

- Lower the head of the machine and lock it in place

using the corresponding pin F (g.1)

- Position the turntable on “0” and lock it in place;

remove the stroke end raised section G (g. 1)

(when present).

- Position the head of the machine at 45° by

unscrewing the knob E (g. 11) and then position

the square A as shown in gure 15.

- Regulate to 45° using the dowel B.

5.7 REGULATION OF HORIZONTAL SURFACE

STROKE END (-45° 0° +45°)

Adjust the screw A (g. 11) to create a stroke end

point for the turntable when the 45° reading on the

turntable matches the same reference index on the

base. Repeat the operation at the symmetrical 45°

reading with the screw on the opposite side of the

base.

6 OPERATION AND USE

6.1 CUTTING SPEED

The type of material and types of cut possible with

the series of mitre saws is vast indeed. The operator

must select the blade to use on the basis of the

material, the cutting speed, and advance of the blade.

Reference to the values above are provided in the

table.

6.2 CUTTING WITH THE BLADE AT 90° AND

TURNTABLE ROTATED (g. 4)

(RI and NTF305 version)

- Release the turntable H (g. 1) by keeping the lever

N (g. 1) pressed down – Rotate the turntable and

select the desired cutting angle using the graduated

scale and then release the lever B. Note: pre-xed

cutting angles are available (0° ±15° ±22°30’ ±30°

±45°) at which the turntable can be locked. We

recommend locking the turntable into position with

the use of the locking knob L (g. 1).

(RP version)

- Release the turntable H (g. 1) using the locking

knob L - Rotate the turntable and select the desired

cutting angle using the graduated scale.

Note: thanks to the “CLIC-CLAC” function, the

turntable automatically locks itself into place at

various pre-xed cutting angles (0° ±15° ±22°30’

±30° ±45°). After locking into position, the application

of a slight pressure is sufcient to rotate the turntable.

Lock the turntable into place using the locking knob L

(g. 1) prior to cutting.

6.3 CUTTING WITH THE BLADE INCLINED AND

THE TURNTABLE POSITIONED AT 0° (g. 5)

WARNING! Remove the support stroke-end raised

section G (g. 1) (when present) before proceeding

to the operation below.

- Release the blade unit by unscrewing the knob

E (g. 11) – Rotate the blade unit and select the

desired cutting angle using the graduated scale,

and then lock into the knob E into position again.

WARNING! Make sure that the support has been

securely fastened with the use of the knob E (g. 11)

when making inclined cuts (g.5-6).

6.4 USE AS MITRE SAW

WARNING! - Make sure that the switch key B (g. 2)

is in the release position (protruding).

- Bring the upper table to its maximum permissible

height and make sure that the blade is completely

protected by the upper casing – Fasten the material

to be cut securely to the cutting surface.

WARNING! Make sure that the blade is completely

protected by the upper casing.

WARNING - The use of the clamp is absolutely

required whenever aluminium sections must be cut.

WARNING - Excessive pressure on the handgrip

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti NTF250 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Felisatti NTF250 Manual

Product: