502513

Felisatti MTF216 Manual

5
Zoom out
Zoom in
Previous page
1/16
Next page
which is raised by the work when it comes close to the cut.
WARNING – these protectors must not be removed, in order
to prevent danger for the operator.
• In the event that the switch lock button has not been
engaged, the machine will stop automatically when the
handgrip is released.
WARNING –engaging thelock buttondisables thesafety
device provided by the manufacturer and enables push-
buttonstart.Itisrecommendedthatthisdevicebeusedwith
theutmostcaution.
The tool has been designed and built so that it is possible to
work in all situations with total safety, however, in special working
conditions, gloves and protective goggles should be worn.
The tool has been designed and built to reduce noise to a
minimum (see technical data), however, in special conditions the
maximum noise level in the workplace might exceed 85 dB(A).
In this case, the operator should protect himself from excessive
noise by using ear protectors.
GENERAL SAFETY REGULATIONS
See manual “Safetyinstructions” which is supplied together
with this instructions manual.
INSTALLATION
1. ELECTRICAL CONNECTION
Before connecting the machine to the mains, one must make sure
that it complies with current regula-tions in the country where it is
used and that the voltage and frequency are as indicated on the
char-acteristics plate.
When extensions are used, make sure that the cross section of
the cables is suited to their length. If using roll up extensions,
make sure that they unroll completely in order to prevent
overheating.
WARNING–beforeplugginginthemachine,makesurethat
theswitchlockbuttonisreleased.
2. WORKPLACE
The tool that you have purchased is a transportable or semi-
stationary electric tool. Only one operator is needed to use it,
given its structure, weight and ease of handling.
In normal use, the operator is in front of the machine with the
handle to his right. The right hand on the handle allows the
machine to be handled completely, in fact, the switch and a safety
hook may be accessed without releasing the handle.
CONSTANT ELECTRONICS
The built-in module permits:
- Soft start.
- The maintenance of a practically constant rated speed up to
rated power.
- An overload protection system by means of current cut-off
in the case of motor overload, in which case the burring machine
shuts down and re-starts when the grinding pressure has been
reduced.
MITRESAWADJUSTMENT-SQUARING
The mitre is delivered by the manufacturer already adjusted and
squared according to standard pa-rameters.
WARNING – before making any adjustment of the mitre,
unplugthemachine.
1. BLADE UNIT LIFTING
An internal spring keeps the motor unit at rest position (raised).
In this position, a safety hook prevents the unit from being
activated accidentally.
1.1 To unlock the motor unit and to be able to use the machine as
a mitre saw, activate the front button D (Fig.1) (the operation may
be carried out with the right hand on the handle).
1.2. To use the machine as a bench circular saw, unlock the
motor unit as indicated in 1.1, and after lowering it completely,
block it with pin P (Fig.1a).
2. BLADE PENETRATION ADJUSTMENT
The depth of penetration has already been adjusted by the
manufacturer during testing.
As incorrect adjustment may cause sharpness to be lost quickly
and/or the teeth of the blade to be broken, further adjustment
might be needed, in which case it will be necessary to work as
follows:
- Activate bolt A (Fig.1а) and the corresponding lock nut to
create a lower limit for the motor housing ideal for preventing
the blades from coming into contact with the turntable.
WARNING–onceforthisoperationiscomplete,makesure
thatthebladeisNOTincontactwiththeturntableandthat
thelocknutistightened.
3. TURNTABLE ADJUSTMENT
0ºRegulation(Fig.3)
- Lower the head of the machine and lock with pin P (Fig.1a).
- Set the turntable to zero.
- Loosen the handles V, remove the guides X – Optional
accessory and loosen bolts Y.
- Set a square between the saw blade and guide M (Fig.1).
- Keeping the turntable at zero, move the guide to 90º on the
square.
- Tighten bolts Y, assemble guides X and adjust handles V –
optional accessory.
4. ADJUSTING THE SAW BLADE WITH RESPECT TO THE
WORKING PLANE
90ºadjustment(Fig.2)
- Lower the head of the machine and lock with pin P (Fig.1a)
- Place a square between the base and the saw blade.
- Loosen lever O and adjust with bolt Z.
- Tighten the lock nut well to make sure that the position is
xed and tighten lever O.
5. VERTICAL PLANE LIMIT STOP ADJUSTMENT (0º - 45º)
(Fig.2)
- Lower the head of the machine and lock it with pin P
(Fig.1a).
- Set the turntable to zero and lock.
- Set the head to 45º and lean a 45º square between the base
and the saw blade.
- Loosen lever O and adjust using bolt Z.
- Regulate the 45º using bolt Z1 (Fig.1a), after releasing the
lock nut.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti MTF216 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti MTF216 in the language / languages: English, German, Spanish as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info