502479

Felisatti HF30 Manual

4
Zoom out
Zoom in
Previous page
1/28
Next page
4
TECHNICAL DATA
Follow very carefully the instructions in this manual, save it
and keep close at hand, ready to carry out any inspection of
parts that may be necessary.
If the machine is used carefully and normal maintenance is
carried out, it will work well for a long time.
The functions and use of the tool you have bought shall be
only those described in this manual. Any other use of the tool
is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See gures)
1. Tool holder (hexagon socket)
2. Front cover
3. Tool retainer
4. ON/OFF switch
5. Lock-on button
6. Supply cord with plug
7. Oil gauge
8. Auxiliary handle
9. Ventilation slots
BRIEF DESCRIPTION
This power tool is designed for chiselling, chipping and
demolishing concrete, rocks and asphalt with high efciency.
A pneumatic percussion unit generates the power necessary
for hammer drilling or chiselling in masonry.
Just like when we hit a conventional chisel with hammer,
a free piston strikes the bit or chisel, which can move
lengthways, through an intermediate part.
This free piston is driven by a second piston activated by an
electric motor through an air cushion. This electro-pneumatic
principle offers great percussion elasticity and work free from
recoil.
BEFORE USING THIS TOOL
WARNING! Before carrying out any work, check, for instance,
using a metal detector, that there are no elec-tric wires or gas
or water pipes under the surfaces you wish to work on.
Make sure the mains voltage is correct: it must be the same
as that on the specication label. Machines with 230V can
also be connected to a 220-V mains supply.
WARNING! Always disconnect the plug from the socket
before doing any work on the machine.
Always check the position of ON/OFF switch. The power tool
must be connected to the power supply socket only when
this switch is in OFF position. If the plug is con-nected to
a receptacle while the power switch is in the ON position,
the power tool will start operating im¬mediately, which could
cause a serious acci¬dent.
• Make sure the cord and the plug are in order. If the
replacement of the supply cord is neces¬sary, this has to be
done by the manufacturer or his agent in order to avoid a
safety hazard.
• Switch off and unplug the machine prior to any proce-
dure on the power tool or in case of mains drop out.
• In case of work area remote from the power source,
use as short as practicable extension cord with proper cross-
section.
• Make sure the auxiliary handle is properly mounted and
securely fastened.
CHANGING THE POSITION OF
THE AUXILIARY HANDLE
hanging the position of the auxiliary handle
1. Unscrew the auxiliary handle M in an anticlockwise
direction.
2. Turn the auxiliary handle M to the required position.
3. Screw the auxiliary handle M in place again.
FITTING THE WORKING TOOLS
1. Clean and then smear the tool shank with grease or
machine oil (Fig. 1).
2. Pull the tool retainer lever (3) toward yourself.
3. Rotate 180° clockwise the tool retainer lever (3) while
pulling it.
4. Next, insert the tool shank into the hexagonal tool holder
(1) on the front cover (2).
5. Clamp the tool by turning the tool retainer (3) by half a turn
in the opposite direction (Fig. 2).To remove the bit, follow the
above described procedures in reverse order.
MAINS CONNECTION
Warning! Connect only to a single-phase AC current supply
and only to the mains voltage specied on the rating plate.
Connection to sockets without earth protec-tion is possible as
the appliance features protective class II insulation according
to European Standard EN50114. Radio interference
suppression complies with the European Standard EN
55014.
SWITCHING ON - SWITCHING OFF
Brief activation:
Model HF25/1500 HF30/2000V
Rated power
W 1500 2000
Impact rate
/min 1400 1500
Impact energy
J 25 11
Tool holder/bit length
mm 30/410
Acoustic pressure
dB(A) 80,6 84,0
Sound-power level
dB(A) 105 106
Vibration acceleration
m/s² 27.0 15,3
Weight according EPTA-Procedure 01/2003 Kg. 16,0 19,8
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti HF30 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti HF30 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info