502482

Felisatti AF125 Manual

6
Zoom out
Zoom in
Previous page
1/45
Next page
6
Do not dispose of electric tools
in the household waste!
In accordance with European Directive 2002/96/EC
relating to old electrical and electronic appliances
and its translation into national law, used electric
tools must be collected separately and recycled in
an ecologically desirable way.
DECLARATION OF
CONFORMITY
We hereby declare, under our sole
responsibility, that the FELISATTI
brand products described in this manual
comply with the following standards
or stan-dard documents: EN60745-
1:2009,EN60745-2-3:2007,EN55014-
1 : 2 0 0 6 + A 1 , E N 5 5 0 1 4 -
2 : 1 9 9 7 + A 1 + A 2 , E N 6 1 0 0 0 - 3 -
2:2006+A1+A2 and EN61000-
3-3:2008 in accordance with EU
Directives 2006/42/EC,2006/95/
EC,2004/108/EC,2002/96/EC.
Francisco Ruis
Technical manager.
We reserve the right to make technical changes 06/2011
To switch off, do the same in reverse.
Constant electronic performance (mod. AF125/1100VES)
The built-in module permits:
- Soft start.
- The maintenance of a practically constant rated speed
up to rated power.
- Speed control.
WORKING INSTRUCTIONS
For cutting or deburring, the part to be worked on must be
secured, unless it is heavy enough to remain in a stable
position by itself.
For optimum performance and results when deburring,
it is advisable that the surface and the disc form an angle
of approximately 30º-40º. Guide the tool by pressing
lightly forwards and backwards. This prevents the part
from overheating or changing colour and the formation of
striations. (Fig. 3)
WARNING! Never use a cutting disc for deburring.
When cutting, do not exert pressure on the disc. Do not tilt
the machine. The disc should not tilt or oscillate. Work with
a steady speed, appropriate for the type of material. When
cutting, bear in mind the direction of the work. Guide the
machine against the direction of the cutting tool, never in the
opposite direction; otherwise there is a risk of the machine
veering off the cutting line uncontrollably. When cutting
proles or rectangular section tubes, we recommend starting
the cut on the shortest side.
ACCESSORIES
Accessories and their corresponding order number can be
found in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying out
work on it.
- Inspect the tool: Using a worn deburring or cutting tool
will diminish the efciency of the work and could damage the
motor.
- Inspect the mounting screws: Regularly inspect all the
mounting screws and ensure they are rmly tight-ened.
Should any screw be loose, tighten it immedi-ately. Failure to
do so could put you at serious risk.
- Motor maintenance: Always take the greatest care over
this and make sure that the motor winding is not damaged
and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is not,
take it to an Ofcial Service Centre to have it replaced.
- Brush replacement: The brushes should be replaced
after 150 200 hours use or when they are less than 10 mm
long. Have this done by an Ofcial Service Centre. We
recommend that at every second change of brushes, you
take the machine to one of our Ofcial Service Centres for
general cleaning and oiling.
- Use only Felisatti accessories and spares. Parts the
changing of which is not covered in this instruction man-ual,
should be replaced in a Felisatti Ofcial Service Cen-tre (See
Warranty/Ofcial Service Centre address leaet).
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti AF125 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti AF125 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info