Manual Fein WSG20-180 (page 20 of 191) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

500381

Zoom out

Zoom in

1/191

For your safety.

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

Hand-guided angle grinder for dry grinding/roughing and

cutting of metal and stone in weather-protected environ-

ments with the application tools and accessories recom-

mended by FEIN.

This power tool is also suitable for use with AC genera-

tors with sufficient power output that correspond to the

Standard ISO 8528, design type G2. This Standard is par-

ticularly not complied with when the so-called distortion

factor exceeds 10 %. When in doubt, please refer to the

generator instruction/specification guide.

Safety Warnings common for Grinding, Sanding,

Wire Brushing, Polishing or Abrasive Cutting Off

operations

This power tool is intended to function as a grinder,

sander, wire brush or cut-off tool. Read all safety warn-

ings, instructions, illustrations and specifications pro-

vided with this power tool. Failure to follow all

instructions listed below may result in electric shock, fire

and/or serious injury.

Operations such as polishing are not recommended to be

performed with this power tool. Operations for which the

power tool was not designed may create a hazard and

cause personal injury.

Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Acces-

sories running faster than their rated speed can break and

fly apart.

The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

The arbor size of wheels, flanges, backing pads or any

other accessory must properly fit the spindle of the power

tool. Accessories with arbor holes that do not match the

mounting hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and

cracks, backing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install an undam-

aged accessory. After inspecting and installing an

accessory, position yourself and bystanders away from

the plane of the rotating accessory and run the power

tool at maximum no-load speed for one minute. Damaged

accessories will normally break apart during this testtime.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stopping small

abrasive or workpiece fragments. The eye protection

must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be

capable of filtrating particles generated by your opera-

tion. Prolonged exposure to high intensity noise may

cause hearing loss.

Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal pro-

tective equipment. Fragments of workpiece or of a bro-

ken accessory may fly away and cause injury beyond

immediate area of operation.

Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting acces-

sory may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and shock the oper-

ator.

Position the cord clear of the spinning accessory. If you

lose control of the power tool, the cord may be cut or

snagged and your hand or arm may be pulled into the

spinning accessory.

Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may

grab the surface and pull the power tool out of your con-

trol.

K... Uncertainty

a m/s

m/s

Vibrational emission value according to EN 60745

(vector sum of three directions)

h,AG

m/s

Mean vibrational value for angle grinding

h,DS

m/s

Mean vibrational value for sanding with sanding

sheet

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

Basic and derived units of measure from the inter-

national system of units SI.

Character Unit of measure,

international

Unit of measure,

national

Explanation

WARNING

OBJ_BUCH-0000000033-001.book Page 20 Wednesday, March 23, 2011 3:51 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein WSG20-180 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,91 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein WSG20-180 Manual

Product: