Manual Fein WSG14 70ET (page 18 of 85) (English, French, Spanish)

502068

Zoom out

Zoom in

1/85

Working instructions.

Before mounting or replacing application tools or accessories, pull the power

plug. This preventive safety measure rules out the danger of injuries through

accidental starting of the power tool.

For each job, use only the FEIN application tool released and intended for the respective

application.

First check that the mains sup-

ply lead and mains plug are

not damaged.

Always hold the power tool

firmly. Otherwise, you could

lose control over the power tool.

WSG10T/WSG14T: Press the locking but-

ton only when the motor is stopped.

Starting (Figure 9).

After inserting the mains plug, the angle grin-

der can be started in any working position by

pressing the pressing surfaces twice in succes-

sion.

➤ Hold the angle grinder in the required

working position, either at the

back (START A) or front (START B); lightly

press at least one of the 4 pressing surfaces,

and keep it/them pressed.

Please note: The accessory begins to move

with short, low-power impulses. The angle

grinder thereby indicates that the first pres-

sing surface has been activated.

For the working position holding the power

tool at the back (START A):

➤ Briefly press one of the front switch-

pads (close to the auxiliary handle) with

your thumb.

For the working position holding the power

tool at the front (START B):

➤ Briefly press one of the rear switch-

pads.

The angle grinder starts gently and rea-

ches its working speed after a short time.

Please note: The angle grinder does not start

up:

– when the switchpads at the front and rear

are pressed at the same time

– when the rapid-clamping lever is not tilted

back and engaged

– if one or more of the pressing surfaces is/

are pressed while the mains plug is inserted

WARNING

CAUTION

➊

➋

Fig. 9

3 41 01 121 21 0.book Seite 18 Mittwoch, 20. Mai 2009 2:23 14

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein WSG14 70ET in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 8,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein WSG14 70ET Manual

Product: