Manual Fein WSG14 70ET (page 5 of 85) (English, French, Spanish)

502068

Zoom out

Zoom in

1/85

The arbor size of wheels, flanges, backing pads

or any other accessory must properly fit the

spindle of the power tool.

Accessories with

arbor holes that do not match the mounting

hardware of the power tool will run out of

balance, vibrate excessively and may cause

loss of control.

Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for

loose or cracked wires. If power tool or acces-

sory is dropped, inspect for damage or install

an undamaged accessory. After inspecting and

installing an accessory, position yourself and

bystanders away from the plane of the rotating

accessory and run the power tool at maximum

no-load speed for one minute.

Damaged acces-

sories will normally break apart during this

test time.

Wear personal protective equipment. Depend-

ing on application, use face shield, safety gog-

gles or safety glasses. As appropriate, wear

dust mask, hearing protectors, gloves and

workshop apron capable of stopping small

abrasive or workpiece fragments.

The eye

protection must be capable of stopping flying

debris generated by various operations. The

dust mask or respirator must be capable of fil-

trating particles generated by your operation.

Prolonged exposure to high intensity noise

may cause hearing loss.

Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment.

Frag-

ments of workpiece or of a broken accessory

may fly away and cause injury beyond imme-

diate area of operation.

Hold power tool by insulated gripping surfaces

only, when performing an operation where the

cutting accessory may contact hidden wiring or

its own cord.

Cutting accessory contacting a

“live” wire may make exposed metal parts of

the power tool “live” and shock the operator.

Position the cord clear of the spinning acces-

sory.

If you lose control of the power tool,

the cord may be cut or snagged and your

hand or arm may be pulled into the spinning

accessory.

Never lay the power tool down until the acces-

sory has come to a complete stop.

The spin-

ning accessory may grab the surface and pull

the power tool out of your control.

Do not run the power tool while carrying it at

your side.

Accidental contact with the spin-

ning accessory could snag your clothing, pull-

ing the accessory into your body.

Regularly clean the power tool’s air vents.

The

motor’s fan will draw the dust inside the

housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

Do not operate the power tool near flammable

materials.

Sparks could ignite these materials.

Do not use accessories that require liquid cool-

ants.

Using water or other liquid coolants

may result in electrocution or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush or

any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory

which in turn causes the uncontrolled power

tool to be forced in the direction opposite of

the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged

or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can

dig into the surface of the material causing the

wheel to climb out or kick out. The wheel

may either jump toward or away from the

operator, depending on direction of the

wheel’s movement at the point of pinching.

Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse

and/or incorrect operating procedures or

conditions and can be avoided by taking

proper precautions as given below.

3 41 01 121 21 0.book Seite 5 Mittwoch, 20. Mai 2009 2:23 14

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein WSG14 70ET in the language / languages: English, French, Spanish as an attachment in your email.

The manual is 8,43 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein WSG14 70ET Manual

Product: