Manual Fein MShy649-1 (page 20 of 96) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

502246

Zoom out

Zoom in

1/96

Hold power tool by insulated gripping surfaces only, when

performing an operation where the cutting accessory may

contact hidden wiring or its own cord. Cutting accessory

contacting a “live” wire may make exposed metal parts of

the power tool “live” and shock the operator.

Position the cord clear of the spinning accessory. If you

lose control of the power tool, the cord may be cut or

snagged and your hand or arm may be pulled into the

spinning accessory.

Never lay the power tool down until the accessory has come

to a complete stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

Regularly clean the power tool’s air vents. The motor’s fan

will draw the dust inside the housing and excessive accu-

mulation of powdered metal may cause electrical haz-

ards.

Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

Do not use accessories that require liquid coolants. Using

water or other liquid coolants may result in electrocution

or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the mate-

rial causing the wheel to climb out or kick out. The wheel

may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or incor-

rect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

Maintain a firm grip on the power tool and position your

body and arm to allow you to resist kickback forces. Always

use auxiliary handle, if provided, for maximum control over

kickback or torque reaction during start-up. The operator

can control torque reactions or kickback forces, if proper

precautions are taken.

Never place your hand near the rotating accessory. Acces-

sory may kickback over your hand.

Do not position your body in the area where power tool will

move if kickback occurs. Kickback will propel the tool in

direction opposite to the wheel’s movement at the point

of snagging.

Use special care when working corners, sharp edges, etc.

Avoid bouncing and snagging the accessory. Corners,

sharp edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or kickback.

Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss

of control over the power tool.

Additional safety instructions for grinding and

cutting off operations

Use only wheel types that are recommended for your power

tool and the specific guard designed for the selected wheel.

Wheels for which the power tool was not designed can-

not be adequately guarded and are unsafe.

Wheels must be used only for recommended applications. For

example: do not grind with the side of cut-off wheel. Abrasive

cut-off wheels are intended for peripheral grinding, side

forces applied to these wheels may cause them to shatter.

Always use undamaged wheel flanges that are of correct

size and shape for your selected wheel. Proper wheel

flanges support the wheel thus reducing the possibility of

wheel breakage. Flanges for cut-off wheels may be differ-

ent from grinding wheel flanges.

Do not use worn down wheels from larger power tools.

Wheels intended for larger power tools are not suitable

for the higher speed of a smaller tool and may burst.

Additional safety warnings

Use elastic spacers/liners when these are provided with the

grinding/sanding accessory.

Make sure that the application tools are mounted in accord-

ance with the manufacturers instructions. The mounted

application tools must be able to rotate freely. Incorrectly

mounted application tools can become loose during

operation and be thrown from the machine.

Handle accessories carefully and store them according to

the manufacturer’s instructions. Damaged accessories can

form cracks and break off during operation.

When using application tools with a threaded insert, take

care that the thread in the application tool is long enough

to hold the spindle length of the power tool. The thread in

the application tool must match the thread on the spindle.

Incorrectly mounted application tools can loosen during

operation and cause injuries.

Beware of any concealed electric cables, gas or water con-

duits; check the working area with a metal detector, for

example, before commencing work.

Use a stationary extraction system, blow out ventilation

slots frequently and connect a residual current device

(RCD) on the line side. When working metal under

extreme operating conditions, it is possible for conduc-

tive dust to settle in the interior of the power tool. The

total insulation of the power tool can be impaired.

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection against

an electric shock will be ineffective. Adhesive labels are

recommended.

Before putting into operation, check the mains connection

and the mains plug for damage.

This machine is also intended to be powered by a.c. gen-

erators with sufficient power output that correspond

with ISO 8528, design class G2. Compliance with this

Standard in particular is not given when the so-called dis-

tortion factor exceeds 10%. When in doubt, inform

yourself about the generator in use.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

3 41 01 079 06 0.book Seite 20 Montag, 15. März 2010 11:24 11

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein MShy649-1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 7,53 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein MShy649-1 Manual

Product: