Manual Fein MF14-180 (page 13 of 77) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

577153

Zoom out

Zoom in

1/77

Regularly clean the power tool’s air vents. The motor’s fan

will draw the dust inside the housing and excessive accu-

mulation of powdered metal may cause electrical haz-

ards.

Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

Do not jam the diamond wheel or apply excessive pressure.

Do not attempt to make an excessive depth of cut. Over-

stressing the diamond wheel increases the loading and

susceptibility to twisting or binding of the wheel in the

cut and the possibility of kickback or wheel breakage.

Do not position your body in front and behind the rotating

diamond wheel. When moving the diamond wheel in the

work piece away from yourself, the possible kickback

may propel the power tool with the spinning wheel

directly at you.

If the diamond wheel should become jammed or when inter-

rupting work, switch the power tool off and hold it motion-

less until the wheel has come to a complete stop. Never

attempt to remove a still running diamond wheel from the

cut, otherwise kickback may occur. Determine and cor-

rect the cause for the jamming.

Do not switch the power tool on again as long as the wheel

is still in the work piece. Allow the diamond wheel to reach

its full speed first before carefully continuing with the cut.

Otherwise the wheel can bind, be forced out of the work

piece or cause kickback.

Use extra caution when making a “pocket cut” into existing

walls or other blind areas. The protruding diamond wheel

may cut gas or water pipes, electrical wiring or objects

that can cause kickback.

Make sure that the application tools are mounted in accord-

ance with the manufacturers instructions. The mounted

application tools must be able to rotate freely. Incorrectly

mounted application tools can become loose during

operation and be thrown from the machine.

Handle diamond wheels carefully and store them according

to the manufacturer’s instructions. Damaged diamond

wheels can develop cracks and burst during operation.

Do not machine any material containing asbestos. Asbestos

is cancerogenic.

Beware of any concealed electric cables, gas or water con-

duits; check the working area with a metal detector, for

example, before commencing work.

Use a dust extraction system, blow out ventilation slots fre-

quently and connect a residual current device (RCD) on the

line side. When working metal under extreme operating

conditions, it is possible for conductive dust to settle in

the interior of the power tool. The total insulation of the

power tool can be impaired.

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection against

an electric shock will be ineffective. Adhesive labels are

recommended.

Always work using the auxiliary handle. The auxiliary han-

dle ensures reliable guidance of the power tool.

Check the diamond wheel before using. Use only undam-

aged diamond wheels.

The mounted diamond wheel must be able to rotate freely.

Carry out a test run for at least 30 seconds with the new

diamond wheel. Use only true-running diamond wheels.

Before putting into operation, check the mains connection

and the mains plug for damage.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Operating instructions.

Before switching on, check the proper operation of the

wheel guard. Set the wheel guard to the completely open

position and then release it. The wheel guard must auto-

matically return to the completely closed position.

Use the construction cutter only with the cover sheet

mounted. (see page 4)

When working, pay attention that an operative vacuum

cleaner is connected. For optimal dust extraction, carry

out a separating cut in clockwise direction.

Press the locking button only when the motor is

stopped. (see page 4)

The self-start prevention lock prevents the power tool

from automatically restarting again, even after a brief

interruption of the power supply, e. g., from a pulled

mains plug. Switch the power tool off and then on again.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power

tool. The total insulation of the power tool can be

impaired. Blow out the interior of the power tool via the

ventilation slots frequently with dry and oil-free com-

pressed air, and connect a residual current device (RCD)

on the line side.

If the supply cord of this power tool is damaged it must

be replaced by a specially prepared cord available

through the FEIN customer service centre.

If required, you can change the following parts yourself:

Application tools, Auxiliary handle.

3 41 01 127 06 0.book Seite 13 Montag, 7. September 2009 12:01 12

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein MF14-180 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein MF14-180 Manual

Product: