Manual Fein MBS25F (page 22 of 72) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

576056

Zoom out

Zoom in

1/72

For your safety.

Intended use of the magnetic drill stand:

Magnetic drill stand for holding a drive motor, for drilling

with solid drill bits, reaming and tapping on materials with

surfaces suitable for magnets in weather-protected envi-

ronments using the application tools and accessories rec-

ommended by FEIN.

Intended use of the industrial drill stand:

Industrial drill stand for holding a drive motor, for drilling

with solid drill bits, reaming and tapping on materials with

surfaces suitable for magnets in weather-protected envi-

ronments using the application tools and accessories rec-

ommended by FEIN.

General safety instructions for drill stands.

Read all safety warnings and all

instructions provided with the mag-

netic drill stand/industrial drill stand or the power tool.

Failure to follow the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all safety warnings and instructions for future ref-

erence.

The term “power tool” used in the safety instructions,

refers to mains-powered power tools (with mains cable)

and to battery-operated power tools (without mains

cable).

Pull the plug from the mains receptacle and/or remove

the battery before making adjustments on the tool or

changing tool accessories. Unintentional switching on of

the power tool is the cause of many accidents.

Before mounting the power tool, install the magnetic drill

stand/industrial drill stand correctly. The correct installa-

tion is important in order to prevent the risk of the drill

stand folding together.

Attach the power tool securely to the magnetic drill

stand/industrial drill stand before using it. Slipping off of

the power tool on the magnetic drill stand/industrial drill

stand can lead to loss of control.

Place the drill stand on a firm, level and horizontal sur-

face. If the drill stand can slip off or wobble, the power

tool cannot be uniformly and securely guided.

Do not overload the magnetic drill stand/industrial drill

stand and do not use it as a ladder or scaffolding. Over-

loading or standing on the magnetic drill stand/industrial

drill stand can lead to the upward shifting of the centre of

gravity of the magnetic drill stand/industrial drill stand and

its tipping over.

Please also observe the relevant national industrial

safety regulations.

Special safety instructions.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses.

Where appropriate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stopping small

abrasive or workpiece fragments. The eye protection

must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be

capable of filtrating particles generated by your opera-

tion. Prolonged exposure to high intensity noise may

cause hearing loss.

When there is danger of falling down, secure the mag-

netic drill stand using the provided lashing strap; espe-

cially when working aloft, on vertical building elements

or overhead. In case of a power failure or when the mains

plug is pulled, the magnetic holding power is not main-

tained.

When working overhead or on vertical surfaces, the cool-

ant container must not be used. Use a coolant spray

instead. Liquids penetrating your electric power tool may

cause electric shock.

Operate the magnetic drill stand only from socket outlets

with the earthing contact according to regulations. Only

use undamaged supply cords and regularly checked

extension cords with earthing contact. A protective con-

ductor without continuity can lead to electric shock.

Do not direct the power tool against yourself, other per-

sons or animals. Danger of injury from sharp or hot

application tools.

Do not rivet or screw any name-plates or signs to the

magnetic drill stand/industrial drill stand. If the insulation

is damaged, protection against an electric shock will be

ineffective. Adhesive labels are recommended.

Do not use accessories not specifically developed or

released by the manufacturer for the magnetic drill

stand/industrial drill stand. Safe operation is not ensured

only because an accessory fits your magnetic drill stand/

industrial drill stand.

Clean the ventilation openings on the power tool at regu-

lar intervals using non-metal tools. The blower of the

motor draws dust into the housing. An excessive accu-

mulation of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connec-

tion and the mains plug for damage.

Recommendation: The tool should always be supplied

with power via a residual current device (RCD) with a

rated current of 30 mA or less.

Operating Instructions.

When a power tool is mounted that is

not intended for use with the mag-

netic drill stand/industrial drill stand, the magnetic drill

stand/industrial drill stand can tip over.

Only use non-water mixable coolants or oil as the cool-

ing agent.

Use the magnetic drill stand/industrial drill stand suitable

for the performance characteristics of your drive motor.

Pay attention that the set-up surface for the magnetic foot

of the magnetic drill stand is flat, clean and rust-free.

Remove varnish and putty/filler layers.

WARNING

OBJ_BUCH-0000000161-001.book Page 22 Tuesday, March 11, 2014 7:56 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein MBS25F in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 9,84 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein MBS25F Manual

Product: