Manual Fein GSZ8-90PEL (page 21 of 200) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

577138

Zoom out

Zoom in

1/200

For your safety.

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

hand-guided straight grinder for dry grinding of metal

with small grinding accessories (grinding points) for shap-

ing metal with hard metal cutters and for cut-off grinding.

GSZ8-90PEL, GSZ11-90PERL, GSZ4-90EL: These

power tools are additionally intended for brushing and

polishing in weather-protected environments with the

accessories recommended by FEIN.

This power tool is also suitable for use with AC genera-

tors with sufficient power output that correspond to the

Standard ISO 8528, design type G2. This Standard is par-

ticularly not complied with when the so-called distortion

factor exceeds 10 %. When in doubt, please refer to the

generator instruction/specification guide.

Safety warnings common for sanding, working

with wire brushes, polishing, grinding, sanding

with sanding discs or cut-off grinding:

This power tool is to be used as a grinder, wire brush, pol-

isher, for grinding, sanding with sanding discs and as a

cut-off grinder. Observe all safety warnings, instructions,

illustrations and specifications provided with this power

tool. Failure to follow all instructions listed below may

result in electric shock, fire and/or serious injury.

Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool. Acces-

sories running faster than their rated speed can break and

fly apart.

The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

Grinding wheels, sanding drums or other accessories

must exactly fit the grinder spindle or collet of your

power tool. Application tools that do not fit exactly in the

tool holder of the power tool will run out of balance,

vibrate excessively and may cause loss of control.

Grinding wheels, sanding drums or cutting tools mounted

on a mandrel, or other accessories must be fully inserted

into the collet or chuck. The “projecting end” as well as

the free part of the mandrel between the grinding acces-

sory and the collet/chuck must be minimal. If the mandrel

is insufficiently clamped or if the overhang of the grinding

accessory is too long, the application tool may become

loose and ejected at high velocity.

Do not use damaged application tools. Before each use,

check application tools such as grinding wheels for chips

and cracks, sanding drums for cracks, wear or heavy use,

and wire brushes for loose or broken wires. If the

machine or application tool is dropped, inspect for dam-

age or install an undamaged application tool. After

inspecting and installing the application tool, position

yourself and bystanders away from the plane of the rotat-

ing application tool and run the machine at maximum no-

load speed for one minute. Damaged application tools will

normally break apart during this test time.

kg kg Weight according to EPTA-Procedure

01/2003

dB dB Sound pressure level

dB dB Sound power level

pCpeak

dB dB Peak sound pressure level

K...

Uncertainty

m/s

Vibrational emission value according to

EN 60745 (vector sum of three direc-

tions)

h,SG

m/s

Vibrational emission value (surface grind-

ing with straight grinder)

h,P

m/s

Vibrational emission value (polishing with

straight grinder)

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

m, s, kg, A, mm, V,

W, Hz, N, °C, dB,

min, m/s

Basic and derived units of measurement

from the international system of units SI.

Character Unit of measurement,

international

Unit of measurement,

national

Explanation

WARNING

OBJ_BUCH-0000000167-001.book Page 21 Tuesday, January 27, 2015 9:01 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein GSZ8-90PEL in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 11,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein GSZ8-90PEL Manual

Product: