Manual Fein FMM350Q (page 17 of 129) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

577145

Zoom out

Zoom in

1/129

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However, if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Emission values for vibration

Operating Instructions.

Do not use accessories not specifically intended and

recommended for this power tool by FEIN. The use of non-

original FEIN accessories can lead to overheating of the

power tool and destroy it.

Guide the power tool toward the work piece only

when switched on.

The application tool can be offset in 45° steps and fas-

tened in the most favourable working position.

Changing the tool (see page 5).

Firmly press in the fastening element to the stop.

Then lock the clamping lever.

Protect your hand and fingers against bruising when

locking the clamping lever. The clamping lever

snaps back vigorously by means of spring force.

Notes on sanding.

Press the power tool with the sanding sheet briefly and

firmly against a flat surface and briefly switch the power

tool on. This provides for good adhesion and prevents

premature wear.

When only one tip or corner of the sanding sheet is

worn, it can be removed again and reattached turned by

120°.

Work with the entire surface of the sanding plate, not

only with the tip.

When sanding with the triangle sanding plate, select a

high oscillating frequency (electronics level 4 –6); when

sanding with the round sanding plate, select a moderate

oscillating frequency (max. electronics level 4).

Sand with continuous motion applying moderate pres-

sure. Applying excessive pressure does not increase the

rate of removal, it only wears off the sanding sheet faster.

Notes on profile sanding.

Select a medium oscillating frequency.

Notes on sawing.

Select a high oscillating frequency. Round saw blades can

be released and clamped offset again, to allow for uni-

form wearing off.

Notes on scraping.

Select a moderate to high oscillating frequency.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power tool.

The total insulation of the power tool can be impaired.

Blow out the interior of the power tool via the ventila-

tion slots frequently with dry and oil-free compressed air,

and connect a residual current device (RCD) on the line

side.

If the supply cord of this power tool is damaged, it must

be replaced by a specially prepared cord available through

the FEIN customer service centre.

For storage of the power tool, remove the application

tool, shut the clamping lever, and then press in the fasten-

ing element.

The current spare parts list for this power tool can be

found in the Internet at www.fein.com.

If required, you can change the following parts yourself:

Fastening element, clamping bolt, application tools

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your power tool may include only

a part of the accessories described or shown in this

Instruction Manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the relevant provisions given on the last

page of this Instruction Manual.

Technical documents at: C. & E. Fein GmbH, C-DB_IA,

D-73529 Schwäbisch Gmünd

Environmental protection, disposal.

Packaging, worn out power tools and accessories should

be sorted for environmental-friendly recycling.

Vibration

Classification of FEIN application

tools according to vibration class

Weighted

acceleration*

VC0

< 2.5 m/s

VC1

< 5 m/s

VC2

< 7 m/s

VC3

< 10 m/s

VC4

< 15 m/s

VC5

> 15 m/s

a 3 m/s

* These values are based on a work cycle consisting of no-load

and full-load operation of the same duration.

For information on the vibration class assigned to the application

tool, please see the enclosed data sheet 3 41 30 421 06 0.

OBJ_BUCH-0000000135-003.book Page 17 Friday, September 26, 2014 12:40 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein FMM350Q in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein FMM350Q Manual

Product: