Manual Fein FMM250Q (page 16 of 120) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

502695

Zoom out

Zoom in

1/120

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Emission values for vibration

Operating instructions.

Do not use accessories not specifically intended and rec-

ommended for this power tool by FEIN. The use of non-

original FEIN accessories can lead to overheating of the

power tool and destroy it.

Guide the power tool toward the work piece only

when switched on.

The application tool can be offset in 45° steps and fas-

tened in the most favourable working position.

Changing the tool (FMM250Q) (see page 5).

Firmly press in the fastening element to the stop.

Then lock the clamping lever.

Protect your hand and fingers against bruising them

when locking the clamping lever. The clamping

lever snaps back vigorously by means of spring

force.

Notes on sanding.

Press the power tool with the sanding sheet briefly and

firmly against a flat surface and briefly switch the power

tool on. This provides for good adhesion and prevents

premature wear.

When only one tip or corner of the sanding sheet is

worn, it can be removed again and reattached turned by

120°.

Work with the entire surface of the sanding plate, not

only with the tip. Select a high oscillating frequency. Sand

with continuous motion applying moderate pressure.

Applying overly pressure does not increase the rate of

removal, it only wears off the sanding sheet faster.

Notes on sawing.

Select a high oscillating frequency. Round saw blades can

be released and clamped offset again, to allow for uni-

form wearing off.

Notes on scraping.

Select a moderate to high oscillating frequency.

Repair and customer service.

When working metal under extreme operat-

ing conditions, it is possible for conductive

dust to settle in the interior of the power tool.

The total insulation of the power tool can be impaired.

Blow out the interior of the power tool via the ventila-

tion slots frequently with dry and oil-free compressed air,

and connect a residual current device (RCD) on the line

side.

If the supply cord of this power tool is damaged, it must

be replaced by a specially prepared cord available through

the FEIN customer service centre.

FMM250Q: For storage of the power tool, remove the

application tool, shut the clamping lever, and then press

in the fastening element.

If required, you can change the following parts yourself:

Fastening element (FMM250Q), clamping bolt (FMM250),

application tools

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

The delivery scope of your power tool may include only

a part of the accessories described or shown in this

instruction manual.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the relevant provisions given on the last

page of this Instruction Manual.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should

be sorted for environmental-friendly recycling.

Vibration a

Classification of FEIN application

tools according to vibration class

Weighted

acceleration*

VC0 < 2.5 m/s

VC1 < 5 m/s

VC2 < 7 m/s

VC3 < 10 m/s

VC4 < 15 m/s

VC5 > 15 m/s

Ka 3 m/s

* These values are based on a work cycle consisting of no-load

and full-load operation of the same duration.

For information on the vibration class assigned to the application

tool, please see the enclosed data sheet 3 41 30 335 06 0.

OBJ_BUCH-0000000018-001.book Page 16 Tuesday, September 14, 2010 11:23 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein FMM250Q in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 6,44 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein FMM250Q Manual

Product: