78185
14
Zoom out
Zoom in
Previous page
1/107
Next page
14
en
The sanding sheet can be pulled off again and then
remounted offset by 120° when only one tip of the sand-
ing sheet is worn.
Securing the work piece.
Secure the workpiece firmly. A work piece that is
gripped tightly in a clamping device or vice, is more
secure than if held by hand.
General operating instructions.
Switching ON and OFF.
First check that the mains supply lead and mains
plug are not damaged.
Switching ON:
Push the switch (2) towards the front (I).
Switching OFF:
Push the switch (2) toward the rear ( ).
Presetting the oscillating frequency (Figure 3).
The oscillating frequency can be pre-selected infinitely
variable.
Increasing the oscillating frequency:
Turn thumbwheel (3) in anticlockwise direction.
Decreasing the oscillating frequency:
Turn thumbwheel (3) in clockwise direction.
The oscillating frequency depends on the application and
the application tool. Example:
High oscillating frequency:
Sanding, sawing, using as a rasp, polishing stone and
metal.
Low oscillating frequency:
Polishing of varnish and veneers.
Working instructions.
Sanding
Typical application: Dry sanding of wood and metal,
especially of smaller surfaces, corners and edges, as well
as hard to reach locations.
Work with the complete surface of the sanding plate, not
only with the tip. Select a high oscillating frequency. Sand
with continuous motion and light pressure. Applying
excessive pressure does not increase material removal;
only the sanding sheet wears more quickly.
Sawing
Typical application: Sawing of thin steel sheet, wood and
plastic components.
Select a high oscillating frequency. Round saw blades can
be loosened and attached offset, in order to provide for
uniform wear.
Scraping
Typical application: Scraping off old coats of varnish or
adhesives, removing bonded carpeting, e. g., on stairs/
steps or other small/medium-sized surfaces.
Select a medium to high oscillating frequency.
For further information as well as tips on polishing, cut-
ting, separating and using as a rasp, see the booklet “Ideas
for Usage”.
Storage (M
ULTIMASTER FMM250Q).
Fully insert the fastening element (6a) into the
tool holder in order to protect it against damage
and contamination.
Engage the quick-clamping lever.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air, and connect a residual current device (RCD)
on the line side.
If the supply cord of this power tool is damaged it must
be replaced by a specially prepared cord available
through the FEIN customer service centre.
If required, you can change the following parts yourself:
Application tools
Fastening element (6a)
Clamping screw (7b)
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer’s warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
instruction manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
3 41 01 078 06 0.book Seite 14 Dienstag, 16. März 2010 7:39 07
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fein FMM 250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fein FMM 250 in the language / languages: German, Dutch, Danish, Italian, Polish, Portuguese, Swedish, Norwegian as an attachment in your email.

The manual is 4,71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fein FMM 250

Fein FMM 250 User Manual - English, French, Spanish - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info