Manual Fein FEIN BSS 1.6 C (page 17 of 59) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

502705

Zoom out

Zoom in

1/59

For your safety.

Read all safety warnings and all instruc-

tions. Failure to follow the warnings

and instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Special safety instructions.

Wear personal protective equipment. Depending on the

application, use a face shield, safety goggles or safety

glasses. Wear ear protection. The safety glasses must be

capable of protecting against flying particles generated by

the various different operations. Prolonged exposure to

high intensity noise may cause loss of hearing.

Wear protective gloves. Hot and sharp chips/swarf can

lead to injuries.

Keep the cutting tools sharp and clean. Cutting tools with

sharp cutters that have been carefully looked after are

less likely to jam and are easier to guide.

Secure the workpiece firmly. A work piece that is gripped

tightly in a clamping device or vice, is more secure than if

held by hand.

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection against

an electric shock will be ineffective. Adhesive labels are

recommended.

Do not use accessories which are not specifically designed

and recommended by the power tool manufacturer. Safe

operation is not ensured merely because an accessory fits

your power tool.

Clean the ventilation openings on the power tool at regular

intervals using non-metal tools. The blower of the motor

draws dust into the housing. An excessive accumulation

of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connection

and the mains plug for damage.

Intended use of the power tool:

hand-guided slitting shears for commercial use for cutting

sheet metal, cut-outs and tight curves in weather-pro-

tected environments using the application tools and

accessories recommended by FEIN.

Operating instructions.

Guide the power tool toward the work piece only

when switched on.

Guide the power tool uniformly and with light feed in the

cutting direction. Excessive feed reduces the tool life of

the application tools.

BSS 1.6 C: For cut-outs, pull the power tool from the chip

while the motor is running. Cut long chips off.

Do not cut steel sheets where welded. Do not cut lay-

ered sheets exceeding the max. work-piece thickness.

To increase the tool life of the blades, it is recommended

to apply a lubricating agent alongside the intended cutting

line:

– for cuts in steel sheet: cutting paste or cutting oil,

– for cuts in aluminium: Petroleum.

For inside cuts, a pilot hole is required; see technical data

for diameters.

Do not switch the power tool off until after having

removed it from the cutting path.

The symptom for worn blades is a clearly increased feed

force at lower working progress.

BSS 1.6, BSS 1.6 C: Punch and cutting bars cannot be

reground.

BSS 2.0: Punch and cutting bars can be reground.

BSS 2.0: For stationary operation, clamp the power tool

in a vice using aluminum or plastic protection jaws.

Tighten the vice adequately so that the application tool is

clamped firmly yet not damaged.

Repair and customer service.

Blow out the interior of the power tool at

regular intervals from outside through the air

vents with dry, compressed air.

Check the application tool for wear every hour.

If the supply cord of this power tool is damaged it must

be replaced by a specially prepared cord available

through the FEIN customer service centre.

If required, you can change the following parts yourself:

Application tools, Cutting bars

Warranty and liability.

The warranty for the product is valid in accordance with

the legal regulations in the country where it is marketed.

In addition, FEIN also provides a guarantee in accordance

with the FEIN manufacturer’s warranty declaration.

Only part of the accessories described or shown in this

instruction manual will be included with your power

tool.

Declaration of conformity.

FEIN declares itself solely responsible for this product

conforming with the documents and standards given on

the last page of this Instruction Manual.

Environmental protection, disposal.

Packaging, worn out power tools and accessories should

be sorted for environment-friendly recycling.

WARNING

3 41 01 111 06 0.book Seite 17 Donnerstag, 10. April 2008 8:11 08

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein FEIN BSS 1.6 C in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein FEIN BSS 1.6 C Manual

Product: