Manual Fein BLK1.3T (page 20 of 118) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish)

502856

Zoom out

Zoom in

1/118

For your safety.

Read all safety warnings and all

instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

Hand-guided nibbler for cutting sheet metal, cut-outs and

tight curves in weather-protected environments without

water supply using the application tools and accessories

recommended by FEIN.

BLK3.5/BLK5.0: This power tool is also suitable for use

with AC generators with sufficient power output that

correspond to the Standard ISO 8528, design type G2.

This Standard is particularly not complied with when the

so-called distortion factor exceeds 10 %. When in doubt,

please refer to the generator instruction/specification

guide.

Special safety instructions.

Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personal injury.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing protectors,

gloves and workshop apron capable of stopping small

abrasive or workpiece fragments. The eye protection

must be capable of stopping flying debris generated by

various operations. The dust mask or respirator must be

capable of filtrating particles generated by your opera-

tion. Prolonged exposure to high intensity noise may

cause hearing loss.

Secure the workpiece firmly. A work piece that is gripped

tightly in a clamping device or vice, is more secure than if

held by hand.

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive

labels are recommended.

Do not use accessories which are not specifically

designed and recommended by the power tool manufac-

turer. Safe operation is not ensured merely because an

accessory fits your power tool.

Clean the ventilation openings on the power tool at regu-

lar intervals using non-metal tools. The blower of the

motor draws dust into the housing. An excessive accu-

mulation of metallic dust can cause an electrical hazard.

Before putting into operation, check the mains connec-

tion and the mains plug for damage.

Recommendation: The tool should always be supplied

with power via a residual current device (RCD) with a

rated current of 30 mA or less.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Operating instructions.

Guide the power tool toward the work piece only

when switched on.

While cutting, hold the power tool as upright as possible

to the work-piece surface.

Guide the power tool uniformly and with light feed in the

cutting direction. Excessive feed reduces the tool life of

the application tools.

Do not cut steel sheets where welded. Do not cut lay-

ered sheets exceeding the max. work-piece thickness.

To increase the tool life of punch and die, it is recom-

mended to apply a lubricating agent alongside the

intended cutting line:

– For cuts in steel sheet: Cutting paste or cutting oil.

– For cuts in aluminium: Petroleum.

For inside cuts, a pilot hole is required; see “Technical

Data” for diameters.

Do not switch the power tool off until after having

removed it from the cutting path.

The symptom for worn punches and dies are a clearly

increased feed force at lower working progress.

BLK1.3T/BLK1.3CS/BLK1.6/BLK1.6L: Punch and die cannot

be reground.

BLK2.0/BLK3.5/BLK5.0: The punch – not the die – can be

reground as long as the length of the reground punch

does not fall below the minimum die length.

WARNING

Die Minimum punch length

BLK2.0:

3 01 09 141 00 3 45 mm

BLK3.5:

3 13 09 093 00 3 51.5 mm

3 13 09 094 00 1 51.5 mm

BLK5.0:

3 13 09 109 00 2 58.8 mm

3 13 09 107 00 0 56.6 mm

3 13 09 108 00 8 54.5 mm

OBJ_BUCH-0000000022-001.book Page 20 Monday, January 31, 2011 9:06 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein BLK1.3T in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein BLK1.3T Manual

Product: