Manual Fein ASCM18 (page 20 of 154) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

576064

Zoom out

Zoom in

1/154

Do not rivet or screw any name-plates or signs onto the

power tool. If the insulation is damaged, protection

against an electric shock will be ineffective. Adhesive

labels are recommended.

Do not use accessories which are not specifically

designed and recommended by the power tool manufac-

turer. Safe operation is not ensured merely because an

accessory fits your power tool.

Clean the ventilation openings on the power tool at regu-

lar intervals using non-metal tools. The blower of the

motor draws dust into the housing. An excessive accu-

mulation of metallic dust can cause an electrical hazard.

Never look or stare into the light of the power tool’s lamp

from a short distance. Never point the light of the lamp

into the eyes of other persons in close vicinity. The radi-

ation produced by the lamp can be harmful for the eye.

Do not direct the power tool against yourself, other per-

sons or animals. Danger of injury from sharp or hot

application tools.

Use and handling of the battery (battery pack).

To avoid hazardous situations such as burns, fire, explo-

sion, skin injuries, and other injuries when handling the

battery, observe the following instructions:

Batteries must not be disassembled, opened or reduced

in size. Do not subject batteries to mechanical impact or

shock. Hazardous vapours and fluid can escape in case of

damage and improper use of the battery. The vapours can

irritate the respiratory system. Liquid ejected from the

battery may cause skin irritations or burns.

When battery fluid from a damaged battery has come into

contact with objects close by, check the respective com-

ponents, clean them or replace them as required.

Keep the battery away from heat and fire. Do not store the

battery in direct sunlight.

Do not remove the battery from its original packaging

until it is going to be used.

Before any work on the machine itself, remove the bat-

tery from the power tool. If the power tool accidentally

starts, there is danger of injury.

Remove the battery only when the power tool is switched

off.

Keep the battery away from children.

Keep the battery clean and protect it against moisture

and water. Clean contaminated battery terminals and

power tool connections with a dry, clean cloth.

Use only intact original FEIN batteries that are intended

for your power tool. When working with and charging

incorrect, damaged, repaired or reconditioned batteries,

imitations or other brands, there is danger of fire and/or

explosion.

Follow the safety warnings in the operating instructions

of the battery charger.

Hand/arm vibrations

The vibration emission level given in this information

sheet has been measured in accordance with a standard-

ised test given in EN 60745 and may be used to compare

one tool with another. It may be used for a preliminary

assessment of exposure.

The declared vibration emission level represents the

main applications of the tool. However, if the tool is used

for different applications, with different accessories or

poorly maintained, the vibration emission may differ.

This may significantly increase the exposure level over

the total working period.

An estimation of the level of exposure to vibration

should also take into account the times when the tool is

switched off or when it is running but not actually doing

the job. This may significantly reduce the exposure level

over the total working period.

Identify additional safety measures to protect the opera-

tor from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation

of work patterns.

Handling hazardous dusts

For work procedures with this power tool where mate-

rial is removed, dusts develop that can be hazardous to

one’s health.

Contact with or inhaling some dust types, e. g. asbestos

and asbestos-containing materials, lead-containing coat-

ings, metal, some wood types, minerals, silicate particles

from materials containing stone, paint solvents, wood

preservatives, antifouling paints for vessels, can trigger

allergic reactions to the operator or bystanders and/or

lead to respiratory infections, cancer, birth defects or

other reproductive harm. The risk from inhaling dusts

depends on the exposition. Use dust extraction matched

appropriately for the developing dust, as well as personal

protective equipment and provide for good ventilation of

the workplace. Leave the processing of asbestos-contain-

ing materials to specialists.

Wood and light-metal dust, hot mixtures of sanding dust

and chemical materials can self-ignite under unfavourable

conditions or cause an explosion. Avoid sparking in the

direction of the dust collector as well as overheating of

the power tool and the materials being sanded, empty the

dust collector/container in time, observe the material

manufacturer’s working instructions, as well as the rele-

vant regulations in your country for the materials being

worked.

Operating Instructions.

Adjust the rotational direction switch and the gear switch

only when the machine is at a complete stop.

Always push the gear switch through to the stop. Other-

wise, the machine can become damaged.

Thermal overload of the power tool is indicated through

flashing of the LED in the handle.

In case of overload, the machine switches off.

To avoid accidental starting, e. g., during transport, set

the rotation selector switch to the centre position.

Electronic torque shut-off (see pages 8– 9).

Adjust the torque only when the machine is at a complete

stop.

OBJ_BUCH-0000000114-002.book Page 20 Tuesday, March 11, 2014 11:02 AM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein ASCM18 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 15,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein ASCM18 Manual

Product: