784931
17
Zoom out
Zoom in
Previous page
1/24
Next page
For further inquiries, please contact our Customer Service Team
Email: ahsservice@watkinsmfg.com Phone: +1 760 598 6464 14
The following procedures should be followed on
initial startup and whenever the spa is drained for
routine maintenance.
FILLING THE SPA WITH
WATER
1. Clear all the debris from your spa.
2. Be sure to open all jets to allow as much air as
possible to escape from the plumbing during the
filling process.
3. Use a garden hose to fill your spa with water.
NOTE: Do not use hot or softened water.
4. As the water level rises, check inside the
equipment compartment for water leaks. It may
be necessary to tighten unions and/or fittings that
may have loosened during delivery. There is no
need to call for service; this can easily be done. If
assistance is required, contact your local Dealer.
Under normal circumstances keep the water level
half way between the top of the spa and the top
of the gray filter ring or just above the highest jets
(whichever is higher).
5. Failure to keep enough water in your spa may
result in damage to your system and invalidate
your warranty. If your spa filter is sucking in air
causing the pump to cavitate, you need to add
water!
IMPORTANT: Loosen drain cap and allow water
to exit hose bib for 5 seconds to help prime the
jet pump, then tighten drain cap. If the jet pump
still is not primed after running repeat step.
6. Check the filter installation and make sure the
filter is not loose.
IMPORTANT: Remember to change your water
every three to four months.
APPLYING POWER
1. Turn power to spa "ON" (after filling spa) from
the main panel at the house and the subpanel.
2. Press the Jets button on the topside control
panel to activate the spa. Rotate all the air
control valves counterclockwise and observe the
increased jet action (air mixed with water).
3. While the pump is running check again for
water leaks at the drain, unions, or fittings in
the equipment compartment (leaks may have
occurred during transit). If water is leaking from
one of these areas, there is no need to call for
service. Simply tighten the fitting. If assistance is
required, contact your local Dealer.
4. After checking your spa for leaks it is now time to
adjust your spa settings. Press the Up or Down
button on your topside control panel until the
display indicates your desired temperature is set.
FILL UP AND START-UP INSTRUCTIONS
UNIONS
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fantasy Splendor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fantasy Splendor in the language / languages: English as an attachment in your email.

The manual is 0.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info